Creo+ and Creo Parametric

Hi,I would like to know what is the shortest way to generate sheet metal dxf flat pattern. Now, i'm using drawing part with empty template and set 1:1 scale. Is it possible to make dxf flat pattern clicking on 3d model? I use this method on the other soft ( SW, UX).Thanks,Adam

Hello expertsHow to create center axis for dia 25 in Drawing using CREO 8, Please some one assist me 

How do I change the default font for drawings, from Font to Arial?    

Hello everyone!I want to calculate the coordinates of the mouse left click point on the solid model.So I tried the following, but the calculation is wrong. pfcSession_ptr mysess = pfcGetProESession();pfcMouseStatus_ptr MouseStatus = mysess->UIGetNextMousePick(pfcMOUSE_BTN_LEFT);pfcPoint3D_ptr Position = MouseStatus->GetPosition();pfcView_ptr view = mysess->GetCurrentModel()->GetCurrentView();pfcTransform3D_ptr Transform3D = view->GetTransform();Transform3D->Invert();pfcPoint3D_ptr model_point = Transform3D->TransformPoint(Position); The “model_point” is wrong .And I can't select points through the function "pfcBaseSession::select()", because there are no points on the surface, I want to calculate the position of the mouse click on the point position on the surface of the solid model.Can anyone tell me how to do it, or is there any other way,thanka!  

Dear Sir/Madam, I've been trying to simulate the behavior of a hub_chain with multiple contacts for more than two months and haven't been able to get good results. I would like to know how a contact_simulation is possible with the software and which criteria have to be considered. I have already created several costing models, including some: Symmetry_Constraints. The chain consists of two pins and eight links. I remain awaiting your response Best regards. Boris.   Translated by the Community Moderation using Google Translate----------------------------------------------------------------------------------------------- Sehr geehrte Damen und Herren,ich versuche seit mehr als zwei Monaten, das Verhalten einer Hub_kette mit mehreren Kontakten zu simulieren, und konnte keine guten Ergebnisse erzielen. Ich möchte wissen, wie eine Kontakt_Simulation mit dem Software möglich ist und welche Kriterien zu berücksichtigen sind. Ich habe bereits mehrere Kalkulationsmodelle erstellt, dar

Switch reference between assembliesAs you can see in the picture, two dimensions of a sketch refer to the assembly "50128267_WC121012" However, this is wrong.I want to have the referencing to the assembly "50128267_WC121012_REVC".How can I change this? Referenzbezug zwischen Baugruppen wechselnWie im Bild ersichtlich, beziehen sich zwei Bemassungen eine Skizze auf die Baugruppe "50128267_WC121012" Dies ist jedoch falsch.Ich möchte die Referenzierung auf die Baugruppe "50128267_WC121012_REVC" habenWie kann ich das wechseln?   

Hello, I try to to analyse gears using the mecanism application in creo 7.0.5.0.When i creating angular motor, this one is greyed out in the mecanism tree:As the consequence, motor can't be used in the analysis :(However when i create linear motor, this one can be retrieve in the analysis definition)Does the problem come from a license that we don't have for angular motors ? Regards,Arnaud   

after the update i found solid welds to still have the weld feature, but they are not shown... to fix this i had to go troug and open all welds, close them and regenerate the model. the problem is with some but welds, for some reason if a intermitted butweld has 1 of the bits of weld cover the original chain selected, it is not shown when the other parst are generated in the 3d model.for 1 interitted weld i had 11 welds and had it end and start with a weld, but the first and last one didnt show.i kind of solved that by trimming the chain by 0.1mm making the weld not cover the original start and end. but for this other weld i have used a short edge in the middle of a round bar and extended it to both ends, the only pice of weld  that dissapears is the one that happens to cover this original edge can someone please fix this as butwelds are anoying enof to make were whenever i enter a value that makes the weld not work, it does not give a preview, basicly making m

I am using Creo Parametric Release 4.0 and DatecodeM130we want to create a custom drill cycle and prepare the code inside the Gpost , the following movements are wanted :1)Approximate feed rate max (G0), coolant :Off, RPM = 500,2) Drill the first deep 1.5 x Ø of the drill with 10% ( 30) of the worging feed rate =F3003) Drill the hole deep with working feef rate (F300) and RPM =3.000 and coolant : ON4) return the to the first deep with F=500 RPM=500TKX

Hello,Is there a way we can find the exact location of bend radius violation in Harness flattening file as we can in creo cabling assembly file?I have been getting a lot of warning in flat file which looks something like the below:WARNING: Min. bend radius of cable CH-02 violated in harness xxxx_FLAT.I tried increasing the bend radius all along the path of the wire CH-02 but still could not get rid of this warning.Is there any resolution for this?    

 Thank you for stopping by this topic. I would like to reduce time to draw complex shape models with Creo. I have location coordinates data of the forms thus I selected each location to draw the shape.If it's possible to draw the geometry directly from the location coordinates, it helps a lot.Do you have any ideas to perform it? Thanks!

Is there a kind soul out there who would like to help me set up the turn-grooving tools?Can't find out how to setup TIP, OFFSET CENTER and so on.Thanks          

Hi! I don't know if I should put it here, if I wish to report a bug (I think SPR)... In my simple part when I add just new revolve, as result the feature will create new body instead the same body and to have it as normally was just additional geometry in the same part I must add boolean operation feature to obtain the single part as it was previously.please review if this is bug -> I am using Creo Parametric 9.0.3.0 BRRoman   

I'm using Creo 4,0, i want to use multiple configurations in assembly using simplified rep, I have gone through some article, but after adding the sets of constraints, I'm unable to call it in simplified rep, while giving "user defined" option in simp rep mode, I'm getting the below error, please assist me.     

How does one make a ribbon cable part without the Cabling application. Simple turns are easy. How to do a twist?   

hey,   I installed the student version of creo 5.0 according to the instructions, but the program does not open. What I noticed, however, is that the terminal says three times: ``0 files will be copied``, and in the instruction video it was 1 file.   Translated by Andra Chirila using Google Translate on March 24th, 2023----------------------------------------------------------------------------------------------- ich habe die schülerversion von creo 5.0 nach anleitung installiert aber das programm öffnet sich nicht. Was mir jedoch aufgefallen ist, ist dass beim terminal drei mal steht : ``0 datein werden kopiert``, und im anleitungsvideo war es 1 datei.         

Hi, My question is on the Result Type - Strain Energy per unit volume 1. After running a Modal Analysis, Strain Energy per Volume can be viewed either  by Graph or by Fringe. What is the difference between them 2. Under the Graph - Strain Energy per volume and selecting a curve, is this the  strain energy of the unit volume or of the the curve ie an edge of the assembly.          

We're OK with the upgrade itself, but what changes can my end users expect? Where can I find some training on the new features for each version?

Working with imports and exports of 3D models, I believe that it is not constant mathematics since it will depend a lot on the model and the source software, but I would argue that it is necessary to have a base of best practices for thisDoes anyone have any kind of document on best practices for importing and exporting 3D models in Creo?  

We become indebted to. I work for Kanzaki Kokyukoki Mfg. Co., Ltd. This is the content that I consulted with Mr. Matsuda of PTC Japan Co., Ltd. in advance.He will get back to you with more details. Currently, we are trying to load the Creo7.0.8.0 model into Altair's Simlab analysis software. However, when I try to read it, the model is not displayed even though the completion message is displayed on Simlab. Creo 2.0, which we used before the upgrade, could read Simlab, but after the upgrade, it is no longer possible to read Simlab. We shared this situation with Altair and confirmed the countermeasures, but we have not received a clear answer yet. I would like to ask you a question, so I made an inquiry. I tried to send the model created with Creo 2.0 and the model created with Creo 7.0, but it could not be attached due to a system error. very sorry.Configuration files, etc. (Please let us know which files to send.) If you have any necessary data, please let us know. If you have any que

I recently updated to Creo 9.0, and the images I've inserted into a notebook file have begun to not show up in the notebook.  This makes using the notebook much more difficult, since the images had references for the various input fields in the notebook.  What's really bizarre is that the problem is intermittent.  In some workspaces, it works fine.  In others, it never works.  In others, it bounces back and forth.  The config for display_images is set to yes, so I know that's not the problem.  When the images don't display, I do get a warning in the log upon opening the file: "Retrieved object was previously saved with display."  I'm not sure how to fix this problem, though.

Hello everyone, I would like to make a drawing for a sheet metal part. I got a step file which I have converted into a sheet metal part (function: Model - Operations - Convert to sheet metal part). This worked fine. See attachements "Step_File" and "Bent_Sheet_Metal". I left it so far in the state "unwind". When I create a 2D drawing from this model I would like to insert the unwinded sheet metal and the bent one. Its not important to have it on one sheet so it can be two sheets seperated (example: 1st.sheet: unwind sheet metal and 2nd.sheet bent sheet metal) To insert the unwinded sheet metal its no problem. As soon as I bent the sheet metal to its final form (like in picture "Step_File") the drawing updates itself (of course) and the part is bent again.  I searched for the problem and found this post but I dont fully understand the steps. Maybe its not even showing my problem. In my point of view its at least near to it. Can someone show me how to insert

Hello community, creating a new combined state with a new appearance state is not possible via toolkit?Is there any workaround out there? Thanks, Lars   

I am using Creo Parametric Release 6.0 and Datecode6.0.6.0Problem with solid center line showing up in a drawing view. Its a offset section with a sketch where there is two lines in 90 degree The section is showed by a full unfold, partial view.Not sure if this is suppose to look like this or if its a bug or if there is any detail settings to hide the solid line that goes through the hole feature?

Dear, How to prepare the nozzle reinforcing pad in creo (refer the attached sketch) dimensionsShell OD - 3000mm x 12 thknozzle od -  1067 mm x 12 thkR.F pad OD - 2000 x 12 thk please provide the step procedure Regards,Robert