Mathcad

1. How can I correct the highlighted functions so that they return 1.00 ft (see image below)?2. Are others experiencing similar issues in this version of Mathcad?3. Is this issue resolved in later versions of the program?Thanks!  

Hello,1.  How to find the intersection points for the below graphs (the red points)?       2. How to find the intersection points for the below graphs (the red points)?     3. How to find following distance between the two peak of blue graph, and between the one peak of the blue graph and one peak of the orange graph from below?       Mathcad Prime 8 file attached.  

I would buy a single license if I could test the trial version.

I am licensed for 8.  How can I download 9?   

I am using Mathcad Prime Release 5.0 and Datecode5.0.0.0I was using Mathcad Prime to perform a series of calculations. After attempting to edit the amount of decimal places I wanted to display, the application froze and then crashed. Before crashing, the file I was working in had saved, however when I attempt to reopen the saved file, the application prompts me with the message written below in the "Error Messages or Warnings" section. I has saved my original file once I created it, however I had not periodically saved while working. The file that did save, saved as a new file on my computer. I was roughly 5 pages into the file and would like to recover my work if at all possible. I am working on a very time sensitive project that will be greatly impacted if this file cannot be recovered.Thank you in advance, Austin PicasoHere are the errors that I facedThe file type is not supported.Log file is located atC:\ProgramData\PTC\MathcadPrime\Logs\MathcadPrime_Exception_20230728_155458.log

  

Newbie question...if I have a matrix of data values as shown below, how can I get Mathcad to solve for the actual polynomial (or exponential) expression ? Or stated another way...can Mathcad provide the actual polynomial formula that would produce the graphed curve below based on the data provided. I am using MathCad V9.0.

Hi,I'm straggling to understand why with solve block i get accurate solution, whereas  writing down the expression i don't get the right answer with arrow and "solve" function..Thanks in advance.      

Just putting this question out there into the Mathcad community, has anyone experienced issues with the installation of mathcad prime 9.0 affecting/losing Windows 10 | Windows Subsystem for Linux (WSL) configurations?  

Hi, I am looking to find a minimum value of 'ey' within a solve block based on a set of equations, which otherwise give a circular reference.So far I cannot manage for the solve block to give me an answer and I was looking for some help. Screenshot of problem:Using PTC Mathcad Prime 8.0.0.0 Thanks,JB

Hello,How to enter and then how to calculate such kind of limits in Mathcad Prime?        

I can no longer find MathCAD Prime under PTC download software. Does anyone know where to find it? I have tried to search for the software no luck. I have received recommendations, but still can't find where the actual software is to download. I have tried to open a case and it referred me to the community. So here I am. Any help would be nice.  

Hi, I converted my file from mathcad 15 version to the new mathcad prim 9.0 and a lot of the functions are not working anymore from before. I have attached the converted file and it is not working properly. Could someone help me fix this issue?      

Hello, I am solving a circuit equation in Mathcad 9.0. I want to express the above equation as cos and sin identities (Basically expanding Euler) .I want the equation to look like U/I form .     

HOW CAN I GET INTERPOLATED VALUES OF KN AT DIFFERENT ANGLES AT A CERTAIN VALUE OF DISPLACEMENT? 

Hello,  

 

Hello Everyone.From :How to fill the ( convex, concave, complex ) quadrilateral with color ?Thanks in advance for your time and help.Best Regards.Loi.

Hi everyone, I have the following table as seen bellow in the attachment and my problem is that I have to extract alphax, alphay, betax and betay based on the value of lambda. Is there any way mathcad can do this on it's own?Thank you in advance.    

I am trying to solve a simulation of blowdown of a pressure vessel and have defined the ODE's but there is a glitch I cannot resolve with a variable undefined error. I am sure it is a trivial error but if anyone can assist I would appreciate it. Mathcad 15 sheet attached.Thanks Ross 

Hi all,I'm new to Mathcad and trying to do somthing that is very simple on Excel, and hopefully isn't too difficult on Mathcad-I have a range variable say z:=-5..5I have a complicated function f(z), but for simplicity just assume it is - f(z):=z^3I would like to have a matrix where the first column is z, and the second coloumn is f(z).It should look something like that--5-125-4-64-3-27-2-8-1-10011283274645125 Any ideas/suggestions how to do it?Thank you 🙂 

 

Hi I am a new user and running into an issue.  I defined a variable outside the solve block and in the solve block set up odesolve with the function in the ODE.  However, I get an error in the solve block saying variable not recognized.  Please let me know what I am doing wrong.

I have installed P9 along side P8.  Some things to note: P9 is not downwards compatible.  I inadvertently saved a sheet in P9 and could not open is P8.  You can copy and paste but only parts.  This should have been made clear in my opinion.P9 HTML help is now PTC web based.  This is of no use if you do not have internet connection or working in a controlled environment. I think this is a poor approach.  the user should be given the option at installation.AnimationThere is some silly plot animation that was installed.  I honestly have no idea what to do with this.If this is an emulation of MCAD animation, this falls very short.Some explanations at the installation would be valuable.Other than that, its the same software as P8 with all its resident deficiencies such as plotting, searching etc. etc. Regards,  

Hello, I've seen this question asked previously but wanted to get some additional confirmation. We are planning to update our license file to allow Prime v9 to be deployed to our users. Will the updated license file for v9 still allow Prime v8 to run? Or will that run on Express mode and not have access to our license?