CAD

Hi Folks,Using Creo 7.0.8.0In the 'Shape' sub-tab of the 'hole' modeling feature ribbon, I recall the graphic used to show the tap-drill depth. I don't see this anymore. Nonetheless, is there a way to add drill depth to the note callout properly? This is omitted and only tap-depth is shown. Thank you. 

Is there a way to change the license server for an existing Mathcad Prime installation without using the GUI within Mathcad? I haven't found anything besides changing the XML file for silent installs, but that's only for before it is installed. I'm able to achieve this for PTC Creo by changing a line in the parametric.psf file and would like to do something similar for Mathcad. Using various versions of Mathcad- 9, 10 and 11.

how creo 7 works in thermal analisys in a steady state ? I mean as input for thermal load i've to consider Heat Flux (W/m^2). This means that load is time dependent. I use a load of 5000W/m^ 2 on a steel structure with 30mm thicknes and i get more than 170°c of temperature. Teoric calculation give me 21 °c after 20 seconds.Does creo consider Fourier time to get Steady State: t= Thickness^2/(Thermal Diffusivity) ? and if it consider that how does it calculate that. Because in material specification ther is not thermal diffusivity value.thanks for answering

We run numerous versions of Creo (7, 10, & 11) to support various clients. The whole mapkey.pro change that PTC has made in Creo 11 has wrecked our config.pro system setup. We have a somewhat complicated setup, so without getting into that I will just explain exactly what I want to try to accomplish. I need to take the users config.pro files and separate them into 2 files; a config.pro with no mapkeys in it, and a mapkey.pro file. I need prior Creo 11 versions (specifically 7 & 10) to load the users mapkeys.pro file from the startin dir. Does anyone know a way I can achieve this? My goal is to keep all of the config.pro files neutral across all versions. I do not want to manage separate user config files for every version, this creates a admi file management nightmare for the way we have our system settings in place.

I am trying to calculate the Jacobian (for a Newton Raphson scheme). At this point the problem is simple enough that I can derive it by hand but I want to make sure the two approaches agree (especially since my hand-derived result is nearly singular). What I am doing is not working - I get a "pattern match" error. Worksheet (in MC11) is attached. Thanks for any suggestions.

I have change device and it seams that i can't download mathcad express. please i'd like some help.Thank you very much.

I purchased a student license for mathcad prime, but when I download my activation file and activate prime 11, even if the license manager says to be activated successfully, the program opens with the express version and says the release is not supported, version 10.0.1 works well.  

My company has been using family tables for fasteners for quite a while and we want to try to use intelligent fastener. All the family tables are stored in Windchill. Is there a way we can use those pre-existing models/family tables with IFX without causing issues across our assemblies?

Hi, Facing the same issue with Creo Illustrate 11.0 Not able to predict the output in video.   Please help asap. Thanks in advance.   Regards, Aditya Gupta

HeyI have a license for MathCad 10 but I can't figure out where to download it, I can only put the license on my MathCad 9 or the MathCad 11 I recently downloaded, can you please help me with a download link to MathCad 10.Thanks.Best Regards,Benjamin

If I use the Include Worksheet function in Mathcad Prime 10, will the worksheet called within the Include Worksheet function path then open and fully run, when calculate is commanded for the primary worksheet?  If I use the Include Worksheet function to call multiple worksheets throughout the primary worksheet, will each of the included worksheets be opened and fully run in sequence when the primary worksheet is calculated?

I would like to suggest an improvement in the Style module and have the Merge, Trim, Extend, Thicken Without a doubt, this would make things easier for users who use this feature. 

Hello,I want to remove hidden lines in my half section (circled red in attached picture) but still have hidden lines activated in the remaning part of the view (circled blue in attached picture) - how can I make this happen? I'm currently on Creo 11Thankful for all the help I can get./ Andreas

How would I add this design to the curved surface of a cylinder? (Creo 8.0)   

I have large assembly drawings that we show the sequence of assembly with various exploded views. We have the full BOM which is usually set to the master simple rep, this has all parts, hardware in the assembly. we also have many assembly steps which I have been making by an saved exploded view with corresponding simple rep (to hide everything not needed for that particular assembly step). Normally in the drawing I show the master rep for the view and use component display to turn off the unwanted parts. This allows me to create associated balloons to the BOM. What I want to do is find a way to create a BOM for each simple rep (exploded assembly step view) and have the item numbers the same as the full BOM (master rep). I don't know if this is possible by writing some sort of relation that looks at the part number in the master and then assigns that item number in the other BOM's of different rep's. I've done a bit of relations writing but this is outside my comfort zone. I can't help

Install problem

Installation

Hey!Im trying to download mathcad express, but somehow I dont get email where download link should be. This is crucial bc I have an exam in few days about concrete desing and I have to use it to calculate stuff.Aaro Ilola

This feels like a silly question, but I have not been able to figure out how to find and replace text in Prime 9 from the help or other posts. 

I'm upgrading from Creo 2 to Creo 8. We use Notes in the model to make string parameters from multiple parameters and have them on different lines. And do I really need to make and place a note in the model then erase it to have this function.As I'm working through it it seems like I do but I'm open to suggestions. Thanks in advance.

Hello everyone. I am opening CEDM models in Creo Parametric. When calculating the mass properties of a mixed assembly (composed of CEDM and Creo Parametric files) I noticed that the Modeling files have the mass at 0 (PRO_MP_MASS). Is there a way to calculate it? All this without modifying the original Modeling file.Thanks to all.Bye Marco

I have added IEAC (Exclude elements autogem control) to my fixed constraint areas. Autogem mesh also reflects the IEAC control. However, in the solver output file, i still see a warning" Excluded elements may be needed near constrain". Is this normal ?

Student assignment and learning from the software

Hi, Can we import CATIA v6 files in Creo illustrate directly? If so what is the version of illustrate? Kindly help. ThanksNaresh

I am using Creo 6.0 and often have issues with these 4 sided tangent boundary blends. The error says it fails to create tangency in the corner. Is there a reason for this? I understand the bounding curves have to be tangent to neighboring surfaces, and I even experimented with making the curves tangent to the whole neighboring surface and not just the neighboring surface parting line. I have tried 3 sided boundary blends but it often got tight in 1 corner and failed.