CAD

Please let me know if there is a good method for creating a winding model when creating a conductor model.Using a helical sweep allows for the creation of a winding with a consistent thickness, but since the coil height is 18mm and the wall thickness is 12.5mm, bending the model created with the helical sweep will cause interference with the coil. If you have a good method, please let me know.Coil SpecificationsOuter Diameter: φ50mmInner Diameter: φ25mmThickness: 18mmWinding SpecificationsWire Diameter: φ2mmNumber of Turns: 13 turnsWinding Arrangement: Wrap around the coil at 115° intervals, with 3 wraps.Gap Between Each Turn: 5°(Calculation: 115° * 3 + 5° * 3 = 360°)ConditionsThe distance between the winding wire and the coil is not constant, resulting in a zigzag shape in cross-section.(Some winding wires will be closer to the coil while others will be farther away.)The winding wires do not overlap.

Building a decent sized harness that will have a few places where things get spliced, found this video which give me some information on a way to do it...https://www.youtube.com/watch?v=n1Ff4-zHkbA Few things I'd like to know is one is this the best way to add splices to a harness? Would there be a way to do it without adding another physical part to the mix? I have not verified this but doing it in this way would create a new wire number (W-1,W-2 etc) for each new wire that comes out of the splice which would show up as individual wires on a to from table in a drawing. Would there be another method that would call out all those wires as one wire number but still allow multiple gauges? If this is the only way then I get it Creo being Creo. I just find it hard to believe that there isn't a way to splice wires without adding another solid body to the harness assembly and just doing it right in the harness menu.

Hello, I am using Notebooks, Relations, and pro program to configure top level General Assemblies. The problem is, I keep getting the following error when regenerating one of our top level assemblies (blurred out some of the numbers): WARNING: More than one common interchange group found.More than one common interchange. Attempting to replace with xxxxxxxx_INT.Pro/Program replace of component xxxxxxxxxxxx (M94) failed in Assembly xxxxxxxxx.Aborting regeneration due to failures executing Pro/Program. The notebook relations to drive parameters are similar to what you see below Starter_name & Starter_Number are parameters. Starter_Number is the part number in windchill 11.0 commonspace. pro/program example is shown below  The issue is that we have a new interchange assembly that is set up correctly to swap these starters. For some reason, Creo wants to use an older interchange that is not set up correctly, but has one of the models inside it. Is

Hello to everyone, I have a new laptop where I have already installed Mathcad Prime 11.00, but some of my old Mathcad 15 files still do not work well in Mathcad Prime when I convert them.I still have the Mathcad 15 package saved in my cloud, but I don't know how to make it work. What should I do to make it to work? regards,  Rogelio

My classmate registered for MathCad (trial subscription) but did not receive any emails from PTC/MathCad. Our professor insists that we use MathCad, but he cannot do homework because his registration never went through. Please advise.

My string library defines three different representations of a string, two of which should already be familar: the string and the vector of character codes. The third type is the vector of characters.   In the following, "str" indicates a string, "vec" indicates a vector of character codes, and "chr" represents a vector of characters. For example, chr2str indicates a conversion from a string to a vector of characters.   chr2str itself is relatively quick, even for long strings. chr2str0 has the limitation of hitting Mathcad's recursion depth limit. chr2str2's use of folding over concat, however, is proving somewhat slow once the string length increases to above about 20,000.   The challenge is to define a faster recursive variant of chr2str.     Where the dependencies are as shown below (except the timer functions, which are in an Area at the top of the attached Mathcad Express 11 worksheet).     Stuart

I am using Creo Parametric Release 10.0 and Datecode10.0.8.0While trying to set up ModelCheck, the instructions say to go to "To configure the Creo ModelCHECK settings, click File > Options > Environment > ModelCHECK Settings." However, that menu option (Environment) is not available to me.How do I get File > Options > Environment to become available to me?Here are the errors that I facedNone

I have a part with Appearance State already defined, how do I "link" that appearance to the assembly? Context:  I already defined 3 appearance states of a part by assigning colors to various surfaces (for texture map, finished product color, and the default model color). In the assembly, is there a way to quickly switch between these Appearance States of the part? The appearance state of the assembly seems completely independent of the part's appearance. I figure it is to be done via layers or representations, but had zero luck. Thank you.

I'm using MathCAD 9.0.0.0. I laid our 2 sets of 3 equations. One set is using variables. The other set has the values plugged straight in. The set with the variables should equal the set with the values because the values are the same, but they don't and none of them equal the correct answer. What should happen is...Rx=Rx=-22Ry=Ry=211.5R=r=213My MathCAD program is written to follow this example...This is how my MathCAD program looks...Ignore the 25 degrees and the 75 degrees in the diagram. This is a homework problem altered to match the example problem so I can test to make sure it works before plugging in the values for the homework problem. Also, I'm interested in fixing the "values" problems Rx, Ry, and r. I only created those to figure out why my variable problems Rx, Ry, and R aren't working. Attached is my program. Thanks,    Brent 

I am using Creo Parametric Release 11.0 and Datecode11.0.6.0Unable to find where Creo Chromium-browser-cache is located for Creo 11.0.6.0 on the client to be able to clear it at every Creo start.

I'm using MathCAD 9.0.0.0. I'm not sure why I'm getting the wrong answer. The calculation should be...R = 329.687 N...but I'm getting...R = 108695.156 NIs there something wrong with my settings? Thanks,    Brent 

I am using Creo Parametric Release 7.0 and Datecode7.0.8.0Basically I’m trying to learn how to create a hole feature UDF with pro program embedded in it where pro program would be prompting user to read values from a text file which would create a different size hole each time the UDF was placed. If I had a part model that had 3 different size tapped holes, could I place the same UDF 3 times but each time read the text file (modified with new values) to create a different size hole (8-32, ¼-20, etc.) Or is this not what Pro Program was intended to do?

Does anyone know why the attached issue is occurring? It seems that when you run units of feet, there is some kind of internal rounding error.

I am using Creo Parametric Release 10.0 and Datecode10.0.3.0We would like help understanding how to edit a Comfort Angle file (mca) for a Manikin comfort analysis.We are trying to correlate the PTC provided zero gravity file with NASA documentation and getting results that don't quite make sense.

When placing a view in a drawing, the boundary of the view is much larger than the actual solid part.  I think it is referencing some datums or ref geo in the view.  Is there a way to get the view to be proportional to the actual solid body in the view?

Hi Creo community, I'd like to get your feedback or opinion on the topic "collaborative engineering on part level"Note that we are using "classical" Creo & Windchill, no Creo+ Request from the users:  We want to execute simultaneous engineering on different areas of a part.See my example:User-1 developing the outside design (or the design already exists)User-2 develops the green areaUser-3 develops the read areaFinally, the "zones" should be merged into one final part and MBD should be addedPersonally I'd prefer a split of the grey part into Bodies and merge them back at the end (boolean operations), the other options could be inheritance or copy geom (surface...) Your opinion on that? BR Georg

I'm using MathCAD 9.0.0.0. How can I use MathCAD to solve for theta? Below is the screen capture of what I have written so far. Attached is my MathCAD file. Thanks,        Brent 

Hello, I'm trying to draw 3D spline go through 5 points defined by matrix "a" .After defining matrix of x range, y and z, these three matrixes are not able to be combined by "augment" function.Are there any way to combine these three xyz matrixes? or any other way to plot xyz?  

I'm using MathCAD 9.0.0.0. Attached is my program. I need to find theta. Theta should equal 32.6 degrees. How can I get MathCAD to solve for theta? Thanks,      Brent 

I am using Creo Parametric Release 10.0 and Datecode10.0.4.0I have written a C executable that will not run unless ucore68.dll is in my Windows path. I want to not be dependent on DLLs if possible.Here are the errors that I faced:The code execution cannot proceed because ucore68.dll was not found. Reinstalling the program may fix this problem.

When we originally did our .Hol files over a decade ago we decided it wasn't possible to call out both FREE and CLOSE in the callout formats.  The Hole note on the drawing could only be shown as a Free(what we set it as). Is that still the case?  When i add in CLOSE to the matrix/table it still just only gives me a Free callout and not the Close when Close is the value set in the model Thanks! DEFAULT_CALLOUT_FORMAT_DATA HOLE_TYPE THREAD DRILLED_DEPTH THREAD_DEPTH CSINK CBORE EXIT_CSINK CALLOUT_FORMAT CLEARANCE NO THRU_ALL NA NO NO NO &HOLE_INSTANCE_COUNT&HOLE_INSTANCE_X_SYMBOL <CTRL-a>n<CTRL-b>&FREE_DEC[.2] DRILL <CTRL-A>x<CTRL-B> &DRILL_DEPTH CLEARANCE NO THRU_ALL NA NO NO NO &HOLE_INSTANCE_COUNT&HOLE_INSTANCE_X_SYMBOL <CTRL-a>n<CTRL-b>&CLOSE_DEC[.2] DRILL <CTRL-A>x<CTRL-B> &DRILL_DEPTH     

We are looking at installing ITI's CADIQ and I was wondering if anyone in the PTC Creo community is already running it and can give us some information. What we are wondering is how it compares to ModelCheck in functionality and quality of the analysis.  ITI has told us that it is an external program, so files need to be saved to disk before running through CADIQ, which is a drawback when we have all of  our data in Windchill.   Love to hear experiences from those that have evaluated or are using CADIQ. Thanks

Hello,I'm using a worksheet in Mathcad prime 11 with the pwrfit function to interpolate the curve of electronic components.Since I like working with units in Mathcad, I slightly modified the interpolation coefficients to include units.Solve this kind of equation, but with the interpolation VPROT = F(I). I is the resultMy goal is to solve a function that uses this interpolation. The solve function doesn't work, but I can find the solution for a single point using a solve block and the Find function.   Could you help me to solve the solve function 🙂 Thank youSee attached file.  

Hidden line removal for quilt not working with 2D cross-section from Sections used. I want image 2,3,4 to be like image 1 that hides hidden line for quilts. If i select 2d section the option of hidden line is greyed out. It does not remove hidden lines. How to fix? Thanks in advance.  More to think ...more to creo!

Hello community!I request your help with the following: I want to enter a matrix into a larger one.I’m working on assembling a global stiffness matrix of a structure (truss)I have defined the matrices of each element. The matrix of the element is 4x4, "i"= 1 to "n", n: number of elementsI have an auxiliary matrix that defines in each row the degrees of freedom associated with each element. For example row 1 contains the degrees of freedom of element 1 and so on. I named this matrix GDL  What I want is for Mathcad to grab the matrix of each element and place it in the global matrix at the positions corresponding to the columns and rows that indicate the row of the auxiliary matrix GDL. For example the stiffness matrix of element 3 must be placed in rows and columns numbers 1, 2,5 y 6 of the global matrix.I understand that once the correct routine is created I would have to use a FOR cycle to do it for each element. But at the moment I’m trying to test with only one element&nbs