Manufacturing (CAM)

When I use the automated chamfering sequence I have a problem. If your chamfer angle doesn't match the tool even by a few minutes or seconds of the chamfer angle it won,t cut the chamfer.When dealing with molds this happens a lot of times for me with drafted surfaces. Here is an example of what I am talking about.the surface circled in blue has a draft on the side wall so the chamfer will not cut it and throws the error message circled in red.I think there needs to be a setable angle tolerance for the chamfer sequence because it is just used to break edges and is not a precise cut by any means. If I want a precise angle chamfer I will surface it with a ball end mill.the work around is to cut it with a trajectory tool path but that is not as easy as just selecting the chamfers with the chamfer sequence.I was wondering if anyone else has seen this problem before I go to tech support?  This thread is inactive and closed by the PTC Community Management Team. If you would like to provi

Hello,I'm trying to generate a G code in CREO 2.0, but the didn't work. The manufacturing have give me just the number senquence of deslocament, but not the G code of operation. Someone new what happened? How I can do it works? Thanks.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

Can any one suggest me steps for getting EMX GENERAL ICON in Creo Mold Cavity..I am using Creo 3.O and I installed EMX 9.O but i am not able to find EMX Icon/tooldbar in Creo Mold Cavity interferance...This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

Dear all,I've made a mold cavity and i want to place it in a moldbase but the size of the cavity is much bigger than the default EMX new project. How can i modify the moldbase so the cavity can fit in?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

Our school system just purchased us a Tormach PCNC 1100  Mill and a Slant 15 Lathe.  The controllers for this equipment only accepts G-Code   We're new to PTC Creo Parametric 3.0 (3 years) - We've worked through the Manufacturing design tool to generate an NCL file, but we don't know how to get the G Code necessary to mill the object. I suspect we need a post processor for this mill, but there isn't one listed for our mill in the menu of choices.   Please advise.   Frank Pendzich Wiesbaden HS FIRST Robotics Club FRC3011 - The RoboWarriorsThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

Hello,         where to download Creo-PDX-Progresive Die Extension?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

After programming a part, I always make a workshop document to show how to do the work. In some specific cases I have to display the tool path on the document. But sometimes, there is more than one view. Is it possible to choose on which view to display the toolpath ?In fact, it displays by default the tool path on the first view created on the drawing.For example, on the view below I would like to show the tool path on the bottom view. But I created the bottom view after the top view. For the moment as a work around, I can delete the first view, display the toolpath on the bottom view, then create again the top view. This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about yo

which postprossecer support herco machining center?in proengineering5.0?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

Hello,  I hope you lovely people don’t mind me asking a question. So I would love to engrave a photo on a block of Al, but the problem I’m having at the moment is how to get a vector photo (i don’t know what is the correct name) into Creo (2.0 version). I would love some advice on how to solve this problem. P.S. Sorry for the bad language, English isn’t my first language and I’m only in high school. Cheers from Slovenija.       

I have creo 2.0 student version.  and i cannot creat the file the mold cavity is uncheckable.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

sir who,s postprossecor in pro-engineer5.0 support herco machine control.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

why ptc silent on the turning canned cycle on creo 3.0??? why there is no builtin turning canned cycle in creo?????regardsasif

In a large assembly, from a project that was concluded in manufacturing some time ago. I need to do some changes. The regeneration times are not acceptable for the time I have to do the job.   I pretend to get "dumb solids", get the geometry whithout features. I was able to do this exporting to neutral and reimporting. Doing this I kept: Geometry, anotations, parameters, layers and datums. Nice, the only thing I missed was the associated drawings, I have to redo several hundred of drawings if I choose this way.   Is there any way to clean up model history maintaning drawings?   JoseThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able

HelloI have borrow a friends computer to make a jig mold..He had not the time to help me, so i ask here. I have no ideé how to cut the rest, I hope there is someone that can help me.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

So older versions of Pro-E you could specify a different color for areas that were removed material. For example I have a casting and that is one color (say purple) but when I make a machining of that casting anywhere I removed material would be a different color (say yellow) so I'd have a purple part with areas of yellow that showed where a machining operation was done.However, I cannot find how to do this in CREO can anyone help?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

is it possible to make nc programming for horizontal milling????if yes then how i do it....please helpThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

how to create the customize material in mold flow analysisThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

I am learning Creo NC(milling) and have run into an issue. When the following situation occurs, it will omit the "G1" causing the tool to enter the next cut at rapid instead of feed. Not good. It appears to be tied to using the parameter value for "free_feed" to anything other than "0"Here is a code example and more info below it explaining the details.If a new sequence is created where the tool repeats, is using “free_feed = 500” or any value other than zero and follows a previous sequence that posts out a “G0” rapid move, then it does not post out a “G1” with the first linear feed move. It will omit it the “G1” and enter the cut in Rapid. If you set the “free_feed = 0” in the constant load vol mill it will then output the “G1” correctly. This will not resolve the problem because the tool then moves in “G0” rapid during the retract tool motions risking damage to the tool and workpiece. The only solution I have found is to set the post to handle the “G1” as non-modal. This resolves the

It’s that time of year again where holiday cheer, quality time with the family, and the good sales at your favorite stores kick into high gear. Instead of re-gifting my gift from last year’s holiday party, I figured I’d give you something you’ll actually enjoy.  Today’s blog post is filled with the gift of holiday cheer. Laugh a little. Laugh a lot. Then spread the holiday cheer by 3D printing holiday gifts for your friends.Laugh a LittleThese engineering memes had our group chuckling right away.Laugh a lotThese engineering jokes from Reddit definitely lightened the mood.A mathematician and engineer are sitting in a bar when the bartender walks up and tells them, "The woman in the corner fancies both of you. One of you should go and talk to her, but every step you take will only halve your current distance to her." The mathematician says, "Well, I guess that's not going to happen then." He pays his tab and leaves. The engineer stands up and takes a few steps when the bartender say

I use solid tools to simulate G code in a full blown seat of Vericut.  I have a solid tool in Creo that is giving me a problem.  The tool design is a 3/8 bull nose end mill with a .06 radius.  When I run the tool path in Creo the tool stays away from drive surface as if it were a regular end mill.  It has been a long time since I have try to setup a solid tool.  Who out there can tell me how to setup a solid tool?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

Hello,I am a highschool robotics team captain, and my team is getting parts cnc'd that I designed in CREO Parametric 3.0. The milling company has requested to have the measurements 2d blueprint style, instead of the dxf, so that they can machine it differently. (less paths using their own generated file.) Is there any way to get a 2d picture of the 3d model with all the measurements, without going into every sketch and recording the measurements? Thanks for the help.~JacobThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

Unfortunately I have a feature I simply can not figure out how to model in Creo, and I would prefer not to model it in solidworks (which can easily create this feature) and then import to creo.The feature is a cut on a planar surface (call it X-Y plane for datuming purposes) generated by a 5/16 diameter , 0.06 radius tipped end mill moving in an arc defined from the tip center of the tool.  the arc is in the X-Z plane and the tool stays parallel to Z while traversing the arc.I can not figure out how to create the feature correctly.  It must be correct for FEA analysis, and has been vetted by experiment to be vastly superior to our older geometry for making similar features, otherwise I would just use different geometry.Any tutorials (I could not find any) or tips to create this geometry?This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You

I'm interested in a solution which supports multiple gates, primarily so I know where weldlines will be. How do these products differ? Are there different tiers of each product as well?ThanksThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

If any one can help me out with this problemThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

I know that some of you have begun playing around with the new functionality in PTC Creo 3.0 M040. And some questions are coming up about how it works, who gets access and what enhancements are coming out next.   Unfortunately I don’t have answers on the last part. But, from what I hear, the plans for PTC Creo 4.0 are exciting. Now, back to those first two questions. Here’s the deal with the new functionality:   How does the new functionality work?   The new design for additive manufacturing (aka 3D Printing) features, are meant to make your life significantly easier when you’re designing and printing. What that means for you is that you can:   Connect and define settings for multiple printers Reduce errors by identifying printability issues before you print Scale, position, and show a clipped view of the model and probable support material on the tray with a “print preview” Save the CAD data, model translation, and position in the tray as one STL file   If y