Manufacturing (CAM)

Hello, I have a question about restricting the tool within the milling window in high-speed machining (HSM), similar to volume milling. I would be very thankful if someone could share any sample files of HSM. regardsAsif 

Requesting EMX team to separate "Return pin" from ejector pin category.  The issue is during cleaning up ejector pins using command " delete all ejector pins" , this return pins will also get deleted and need to reassign all the references related to it. kindly check.

Hi everyone,I’m currently exploring Creo’s multi-axis manufacturing capabilities, specifically for impeller machining. I’ve already programmed and machined an impeller using Creo Multi-Axis, but all the strategies—roughing, blade finishing, and hub machining—had to be created manually. (Please see attached picture.)Other CAM software like Mastercam and Siemens NX offer dedicated modules or toolpaths tailored for impellers and other bladed components.So I’d like to ask:Does Creo offer any specialized tools or modules for 5-axis impeller machining?Are there built-in strategies for blade-to-blade finishing, tool tilting and collision avoidance, and roughing in deep/narrow passages?What about hub finishing with smooth transitions?Or is everything expected to be built manually through generic multi-axis features?I’d appreciate input from anyone who has experience machining turbomachinery parts in Creo.Thanks in advance!

Profile Milling with Tool Compensation and Ramp Entry or helical for Internal Profile Hello CREO Users,I am working on a milling operation for an internal profile (similar to a valve seat geometry) in Creo Manufacturing. My objective is to machine the internal contour using tool radius compensation (CUTCOM) and to ensure smooth ramp transitions between Z-level passes or using helical folling the profile to avoid marks on the final surface.I have tried the following approaches:The Cut Line strategy allows helical movements and smooth transitions between passes, but it does not support tool radius compensation (CUTCOM). This is a requirement for my process.The Profile Milling strategy does support CUTCOM, but it does not offer ramp or spiral entry between Z-level cuts. As a result, the tool plunges vertically at each level, which causes unwanted marks and steps in the internal diameter of the part.I've tried to explore all the SCAN_TYPE parameters. LEAD_IN and LEAD_OUT approach but

Hello, I receive the errror message listed in subject line when trying to post an NC file.  I have set the "ncpost_type" setting in the configuration editor previously.  I am using Creo 9.   Any help is appreciated.  

Hello  Is Creo Parametric CAM software outputting tilted work plane or dynamic fixture offsets?If yes, then how do  we use it with the combination of the post-processor regards Asif

hello experts I am asif from Karachi, Pakistan i have a question about the Creo post processor. How to add Pivot distance in dual rotary table 5-axis machine with PTC Creo. and  Swivel-Type (Head-Head) 5-Axis CNC in creo post processor. Please check the pic of the machine configuration. i want to update the post processor for both machines. Please guide. regards Asif

I'm trying to use a subroutine to create multiple parts in one program.  But instead of incrementing the position each time, it just cuts the first part position over and over again.  I've tried absolute / incremental, and I've tried the different "base coordinate system" options, and they all have the same effect.  My post isn't set up for subroutine program calls, so I always have "Copy CL" selected.  The simulation shows all 400 parts being cut correctly, but on the machine, only the first position is cut (over and over). It always outputs a fixture coordinate system (G110, G111, G112, etc.) and the X/Y positions just stay the same in each block.  I want the X/Y positions to increment with each block.  Anybody know what I'm doing wrong?  Or if there is some post option I need to edit? 

 Hi everyone, I just got access to Creo 11 and I'm struggling with one of the new features they added.For this model I want to use 4 axis HSM, however even if I select the B axis as rotatory (which means it rotates around the Y axis) the machining area I can select is always a cylinder around the Z axis and I can't figure out how to change it. My work center settings also specify it revolves around the Y axis but it just doesn't allow me to change the axis of the machining area. Any idea on how to solve this?

Good day.Has anyone encountered this error message in the log of messages?No relations have been defined for this model.I am seeing this in a few of our programs but cannot seem to find any "wrong" relations within the various parts or sequences.This creates an extremely long set of log messages which cannot seem to be resolved.I have found this article from Creo3 (2015) but with zero answer to this specific message inside, despite mentioning it... Currently on Creo 9.https://www.ptc.com/en/support/article/CS196584If there are no relations and it  provides this error, is Creo indicating a requirement for relations in the sequences?Any help would be much appreciated.

Would anyone care to comment on the Mold Machining Extension (MMX)?  What does it offer over and above what is in the NC complete set module for 3 axis milling?

Hello Creo experts,I have a question regarding volume milling. I have often chosen to use rough or HSM sequences instead of volume milling for roughing operations. However, I've noticed that the cycle time for HSM and rough sequences is not as good as I expected. Despite being named high-speed milling, the cycle time is actually longer than the volume milling cycle for the same pocket size. Can you please advise on the parameters I may be missing to achieve a shorter cycle time compared to volume milling on the same size pocket?Regards,Asif Fisa

Hello, dear community members!I want to design a mold cavity, but I am stuck on "Volume Split." I can't run this command, and after doing some research, I noticed that the problem is related to the "Parting Surface." I received the following error: The parting surface has 3 contour(s), make sure that each is necessary. Could you please help me solve it? Please check the attachments as well.

I am using Creo Parametric Release 2.0 and DatecodeM040abbiamo spostato correttamente creo m040 dal vecchio pc al nuovo, ma la parte CAM non funziona. non apre nemmeno il file di fabbricazione.Here are the errors that I facedabbiamo spostato correttamente creo m040 dal vecchio pc al nuovo, ma la parte CAM non funziona. non apre nemmeno il file di fabbricazione.

I am using Creo Parametric Release 2.0 and DatecodeM040abbiamo trasferito la versione da un vecchio pc a questo, ma la parte di manufacturing non funziona e non apre neanche i file di fabbricazioneHere are the errors that I facedabbiamo trasferito la versione da un vecchio pc a questo, ma la parte di manufacturing non funziona e non apre neanche i file di fabbricazione

Hello, I am currently using the base EMX extension and I noticed the extension utilizes injection molding. I wanted to know if the EMX extension is capable of creating plates/molds for pulp molding? Thank you.

  Hello Creo Experts, I have a question regarding volume milling. I typically choose volume rough milling sequences for my roughing operations. But now trying to use HSM Milling.. However, I've noticed that the cycle times of HSM sequences are not as efficient as I expected. Despite their name, high-speed milling cycles are actually longer than those of volume milling for the same pocket size. Could you please advise me on any parameters I might be overlooking to achieve a shorter cycle time with HSM or rough sequences compared to volume milling for the same pocket size? Please check the attached MFG file its creo 11 mfg file  Regards, Asif Fisa

I am using Creo Parametric Release 10.0 and Datecode10.0.5.0For hole making manufacturing sequences, for whatever reason ours defaults to all models instead of reference model. To be more clear, I'm referring to when you click on the Mill tab>Holemaking Cycles>Standard (or whatever floats your boat)>References>Details>Options...the dropdown here defaults to All Models, and I am wanting it to default to reference models, since i am setting my reference model. As you can imagine, when we go to make a new program based off of an existing one, and we remove a fixture component, it causes manufacturing sequences to fail because they are being tied to these random models instead of just to the reference model.I have searched config.pro options and the knowledge database and I'm finding nothing that can point me in the right direction on whether the default to this can be set when creating new sequences. If this does not already exist, can this be added as a config.pro option?

I have a problem with the mouse in the mould base definition window, when I place the mouse over a plate it does not select to select it I have to move it either to the side or higher up,has anyone ever had this problem? if so how did you solve it?i have also tried with older versions but always the same problem.

I am in Creo Parametric 9.0.8.0. I am attempting to generate an MCD in Creo NC. I am able to generate an NCL file with no issues. However, when I try to generate an MCD file, after all of the prompts, I check my working directory and there is no file for the g-code output. I have attached an image of the log. Am I missing something here? 

I can set up a new table add the repeat region and add in the "file path" (no clue what you call it) to each cell. ex. terminal information  - mbr.terminal  For the entry ports/pin I found this file path on youtube mbr.connprm.pin.name. when I first make the harness I designate the connector and assign each entry port a coordinate system to work of off and then add in the entry port when I designate each connector. It also looks like other things aren't working either like if I wanted the wire color or the wire gauge going to the connector. I know I'm missing something I just can't figure out what.

Hi, Is there any possible way to enable or use autosave in Creo Parametric 6.0 ? We are working with large assemblies and program crashes suddenly if you are working something complex. Thanks in advance, -Enes

Did PTC ever fix the volume not remembering it's name issue they created in Creo4 and (as far as I know) carried it into every version past? Last time I checked it was still there (must be years now) even though it was a known issue that broke the mold design package. 

We use Creo 8.0.6.0. Is there a newer version of Autoaxis for Creo8?  

Hi,did any of you has an experience with the following topic ?i searched the knowledge base and found only reference to old documentation.Many thanks,