PTC Education Forum

Hello All, Greetings! We have a peculiar scenario in which a command or set of commands work in one version of Creo Parametric but does not work in the other.  Solidify does not work in a direct manner on an offset surface/quilt in Version 11.0.1.0 but works straightaway in Version 11.0.5.0 by selecting the surface and it finishes the task!...I wish to know what made this difference. Are there a few patches installed in the later version, I mean. How can we know what is the difference between the two versions? Where can I find this information? I will appreciate if someone can please provide guidance. Thanks a ton. 

I want to take a licence or take 60 days free. I'm a student, please give me free use. 

 Bonjour,Je rencontre un problème avec la configuration de Creo Parametric 10.0.9.0. Les unités par défaut sont  les Pouce Livre Second. Or j'aimerais configurer mon logiciel afin que les unité métrique soit par défaut. Malgré la création et le placement d’un fichier config.pro personnalisé, le logiciel ne semble pas le prendre en compte au démarrage. Les unité reste en systèmes impériale et les fichier de configuration lu indique C:\Users\hugos\Documents\config.pro alors qu'il n'y a pas de fichier a cette emplacement. Y a t'il une autre méthode ? Informations techniques :Version de Creo : Creo Parametric 10.0.9.0Système d’exploitation : Windows 10 (64 bits)Chemin d’installation :C:\Program Files\PTC\Creo 10.0.9.0\Parametric\bin\parametric.exeChemin du fichier que je souhaite utiliser :C:\Users\hugos\Documents\PTC\Creo10.0\config.proFichier actuellement lu selon Fichier → Aide → Informations système : C:\Users\Public\Documents\config.pro C:\Progr

I want to make a bubble chart by by definingi = 1 to 32j = 1 to 32so that 32 x 32 = 1024 points are generatedlike as follows(1,1), (1,2) , ... , (1,32)(2,1), (2,2) , ... , (2,32)...(32,1), (32,2) , ... , (32,32)the final output needed is 

I had an issue with my computer and had to reset / fresh install Windows. On Login, I see: "You have reached the maximum number of license requests available for your product type." After searching high and low in these forums, I found this link, which is also not helpful:https://support.ptc.com/appserver/lm/programs/licensing_programs_v.jsp It says its meant to "Transfer an Existing Student License" (which I think is what I want to do) - from https://community.ptc.com/t5/Mathcad-Tips/Transferring-Mathcad-Single-User-or-Student-license-from-an/ta-p/819143#M1600 but it gives the same unhelpful message that says: "Thank you for using Mathcad. You have reached the maximum number of license requests available for your product type. To upgrade to the latest version of Mathcad, please visit store.ptc.com." Isn't this the whole point of the transfer tool?Incredibly frustrated after purchasing the license. 

I have an Education version of Creo 11 but need to move this to a new PC. The nature of the existing license does not allow me access to the licence manager tool or e-support. Is there anyone who can give me some advice please. Many thanks

Good morning, Our school robotics team is currently participating in the FTC competition, and we’re in the process of organizing all the models in Onshape. The "FIRST team" kindly shared a file with us, but I’m having trouble figuring out how to identify the material of the parts used in the model.If someone could assist me with this, it would be greatly appreciated!

Hello! I'm student and I need license for CREO 5. You can help me?

PTC community please help mi when I move to license identification process there is showing success but the finish button is not able to clickPlease help me   

hello sirI am installing creo 11.0.5.0 student version but after installation, I am getting below error. kindly help to solve issue 

I am using Creo Parametric Release 12.4 and Datecode12.4.0.0Trying to use Engineering Notebook and it says that our Educational edition has no license. We have been able to use this in previous years. Have done a full uninstall and reinstalled selecting the addon Engineering Notebook.Here are the errors that I facedYou do not have a license for Engineering Notebook. Please check with your administrator.

I have already submited the online form (https://www.mathcad.com/en/try-and-buy/mathcad-express-free-download) multiple times since yesterday, but I have not yet recevied the download link.

Hi!I've filled in the form to get the link to the Mathcad Express university version but the link just won't appear in my inbox. Yes I have checked the spam and yes my email is correctly typed in. I'd really need it ASAP. THanks for any help.

PLEASE, I NEED TO ACCESS TENS OF ACADEMIC WORKS, AND MY VERSION OF MATHCAD IS NOT WORKING, I NEED TO DOWNLOAD, REINSTALL AND REACTIVATE IN MY NEW COMPUTER. THANKS.

Issue: Error - "Creo Agent did not initialize correctly. Please contact technical support if the issue persists".     Reasons/Causes:- Error message indicates that creoagent.exe either has not been launched or has exited prematurely Encryption software or antivirus software cause this issue Fail to install creoagent.exe Unable to install Creo Platform service due to lack of admin privileges Solution: -   Browse to Creo Parametric Trial installation folder C:\Program Files\PTC\Creo 8.0.0.0\InstallManager     Run creosvcs_64.exe as an administrator   This should help resolve the error encountered.

Hello PTC Academic Support,I’m a student trying to run Creo Parametric and my node-locked student license is failing with:• “License request failed for feature … license.dat: (-9) Invalid host.”• When I run reconfigure.exe and enter my product code, I get: “You have reached the maximum number of license requests available for your product type.”Could you please reset my student license activations or reissue a license tied to my current host ID?Details:• Product code originally used: BK120908EDUNIVERSITYED• PTC Academic account email: poor0041@umn.eduIt would work when I would try to reconfigure it but now I have run out of license. but it only doesn't work on EDroam wifi it seems. • Computer name: Nicks-Laptop• OS: Windows 10 (Version 10.0.26100.6584)• Current active adapter MAC (host ID): 3E-C3-27-C4-FE-F2• License file HOSTID currently tied to: 32-DA-63-A1-9A-2F• Error dialogs: “(-9) Invalid host” in Creo; “maximum number of license requests” in reconfigure.exe• License files p

I purchased the license for Mathcad Prime 11 Student Edition, but when I attempt to activate it, I receive an error stating that I have reached the maximum number of license requests available for my product type. I have not used or activated my product key on any other device, so I am confused why I am getting this error message. I tried the online license portal, but it gave me the same error. I've included pictures of the error message and some information to help figure this out. Host ID: DC-21-48-00-77-A1

Hello everyone,I am working with Creo Flow Analysis on a model of a beaker filled with water (fluid domain). To close the volume, I created a capping surface at the fluid level.Now, I want to add a pipe as a second fluid domain that penetrates this capping surface and goes into the beaker. My idea is to define the upper circular face of the pipe as an inlet and define the lower circular face of the pipe (inside the water) as an outlet.The problem: Because the pipe passes through the capping surface, I cannot select the lower circular face of the pipe as an outlet in the Assistant.So my question is: What is the correct modeling approach in Creo Flow Analysis if I want to have a pipe fluid domain inside another fluid domain, with its upper face as inlet and its lower face as outlet? Thanks a lot for any advice!

Somethings wrong with the licence ?  

I did as the download instructions but it didn't work and I don't know where the error is. Please help me solve this problem. Thanks

I have downloaded the student version of Creo 12 and upon opening Creo Parametric I get the following error message: Error codes 21 and 5 show up. How do I resolve this issue? Please help 

I recently downloaded Creo 12.0. When I attempt to install the license, after I punch in the code provided by the held pdf, I receive an error message.

Hi, my student license for Creo Parametric 12.0 is going to expire. I see that on the internet, the message is supposed to have a 'Renew License' button with it, but that is not available for me. Please guide me.

This file is in MathCAD 9, but I'm experiencing the same issue in MathCAD 10. I believe MathCAD is misrepresenting the units. See attached. "Hmp" and "TH" have the wrong values when comparing with example 11.2 at the bottom. I rewrote them as H and T next to them. I substituted "m" and "Ump" for the actual values of 100000 and 1035 and the answers came out correct. So, something is wrong with how "m" and "Ump" are represented.

I purchased the student edition of Mathcad for a class I am taking this semester. I was having issues with the download on my laptop, and there was an assignment due, so I went ahead and downloaded it on my PC. I just tried to download Mathcad on my laptop, and it is saying "You have reached the maximum number of license requests available for your product type." I was unaware that I would not be able to use the software on multiple devices, and it is much more important for me to have it on my laptop than PC. Is there a way I can get the software on my laptop without having the purchase another license?