CAD

I am using Creo Simulate Release 9.0 and Datecode9.0.0.0Not converge for prescribed translationHere are the errors that I faced** Warning: Convergence was not obtained because the maximum           polynomial order of 4 was reached.

Is there a way to change the license server for an existing Mathcad Prime installation without using the GUI within Mathcad? I haven't found anything besides changing the XML file for silent installs, but that's only for before it is installed. I'm able to achieve this for PTC Creo by changing a line in the parametric.psf file and would like to do something similar for Mathcad. Using various versions of Mathcad- 9, 10 and 11.

Hello,I’m working on a 2-speed transmission model in Creo Mechanism, and I need some help setting up the dynamic gear engagement behavior. The transmission has a neutral, 1st gear, and 2nd gear.I start the mechanism analysis in neutral condition.The input shaft is driven by a servo motor rotating at 1000 RPM.A second servo motor is used for gear shifting (e.g., a sliding collar or actuator).           In neutral, all gear connections should be disengaged.When the output shaft engages with 1st gear, only 1st gear should be active, others disengaged.Similarly, in 2nd gear, only the 2nd gear should engage.All this should happen in one continuous analysis, driven by:One input servo motor (rotating shaft),One shifting servo motor (for gear selection).How can I simulate this type of dynamic gear engagement/disengagement in Creo Mechanism using just one servo motor for input and another for gear shifting? 

Hello everyone,We just upgraded to CREO 11 from CREO 7.   Axis are showing up as solid lines in models in 11 but show as center line 7.  I've been looking for a config setting or something to fix it with no luck.  Gets to be a mess with large parts.  They display better in drawings, you can zoom in and see it's a center line at least.  They show up correctly when printed. Any suggestions?Thanks  

Hello, anyone knows how to change the background color of mathcad prime 1.0 sheet.thanks in advance for your help.

Is it possible to add a dimension reference to an existing ordinate dimension? In the image below, the top hole is a new feature. I want to add it to the existing ordinate dimensions, but can't figure out how without deleting everything and starting over.  

I want to understand how difficult it would be to reproduce this functionality using the free version of JLink. Currently, we have some Smart Assembly licenses and use them for placing UDFs. How challenging would it be to achieve the same with JLink, so we can deploy to a larger group without relying on Smart Assembly licenses? Here is a sample bit of code that we use in Smart Assembly. Basically, it shows an image of what to select, and then the user makes a selection, which Smart Assembly uses to place the UDF.MESSAGE_BOX_EX IMAGE lib:PIC\TC_00_0.GIF GENERAL "TOPCAP AXIS" "SELECT TUBE SURFACE" BUTTONS JUNK USER_SELECT SURFACE TUBE_SURFACE CREATE_UDF lib:udf\new_axis THIS UDF_GROUP UDF_REF TUBE_SURFACE TUBE_SURFACE END_CREATE_UDF GET_GROUP_FEATURE UDF_GROUP 1 GROUP_FEA SET_REF_NAME GROUP_FEA "SA_TOP_CAP_AXIS" UNGROUP_FEATURES UDF_GROUP SEARCH_MDL_REF EXCLUDE_INHERITED THIS AXIS "SA_TOP_CAP_AXIS" TOP_CAP_SPRING_AXIS

Hi Dear,   I am having a 2D Drawing which requires to show Dual dimensioning in a table for BOM. Option 1 (See attached image) :Right now by default in Creo 2D Drawing the dimensions shows up Top[mm] and Bottom[Inch]. Option 2 (see attached Image) : I would like to show dimensions side by side - Calling dimensions from Model. Left [mm] right sixe [Inch]. (I have manually written as of now in this image),I would appreciate if you can adivse how can I achieve option 2 for dimensions that are called from Model? Thanks so much in advance.

I solved a statics problem with Mathcad Prime 10 like this:Can any member suggest an elegant method to do this?

Afternoon,I am using the Mathcad Prime 10. I'm fairly new to Mathcad so there may be an obvious answer to this. I have a few graphs like this, and am needing to determine the value of v for each curve (green/blue) that gives a Y value of the red line. Is there an easy way to do this? Also, unrelated and mostly a formatting request, the Y-axis is Pressure, and will only display in Pa, I would prefer psi for this situation but cannot for the life on me figure out if I can change it. Any ideas? Thanks for your help in advance.

Creo is creating these loops when I route the cable, but they are not shown in the network routing. Yes, the network is continuous. The cable assembly is 4 separate connectors but the wires from one go to different connectors so they need to be on the same network. I'm not sure why this is happening. I am not recieving any network errors.

After choosing a bolt and corresponding nut, I get the attached error.  The hole in the first part is created, but the hole in the second part of the bolted assembly does not get created.

I'm trying to create an R1/8 threaded hole as a mate to the component in the picture. The component is an R1/8 to 12mm push fit adapter. I tried to create a thread using the helix sweep feature but was unsuccessful. if someone could point me in the right direction, it would be very much appreciated.  

I am using Creo 9 and trying to align freestyle shape(s) to facet feature; not finding any way to do this.my goal is to make smooth shape from stl feature then be able to "shell" the model any help is greatly appreciatedthanksRich

Hi, I am trying to create a new format with titleblock & other model details. When the parameters are added in the title block the same is not updated when model is called in the drawing sheet. Kindy help.ThanksNaresh

 Does anyone know why this is happening? I set all the "B" Labels to "Variable" and it still says undefined.   I got this example from a youtube video and it gives a different error.  This is pretty frustrating, not gonna lie. I am new to mathcad, so maybe it's something I'm doing.Here's to hoping you can help.Thanks

As per the original post..    Martin,   Do you know if it possible to include conditional statements in a psf file?I'd like to be able to do something like the following, but it doesn't seem to to work:IF !DEFINE(CREOCACHEDRIVE)     ENV=CREOCACHEDRIVE=C:ENDIF

Can you change the color of the Mathcad sheet background? Why is this still an issue in 2025?

I had installed an educational version for trial on an old laptop, but it didn't run well because of the bad hardware features. Now I just bought a latest generation PC and I would like to try it, but I can't install it because of licensing problems.

Why does the third solve block not work?   (Mathcad Prime 9)    

Dear all,   I have a big troubles to import jt files from some customer and almost find the reason from the topic.  Current my JT file assembly name have no hypens but most of parts name have hypens...  When I imported this jt files to creo, It takes almost 20 minutes  and hypen name have changed to under bar...   JT2GO just takes 30 seconds to show this model.    Creo imported 20 minutes  And some parts  disappeared in creo compare to JT2GO parts ,,  Is anyone have this kinds of issues ??   If the my customer changes parts name,  It will be clear ?? I just ask this here because customer maybe don't want to change.   Anyway,  thanks a lot to give a hints from all of you.   

I'm trying to plot a couple shear-moment diagrams, and have reactions in the middle of the beam causing the shear diagram below to jump discontinuously. How do I represent those jumps with vertical lines connecting them?  

After opening the 3D model in Creo Prametric↓File↓Save As↓Save a Copy↓Type: PDF U3D(*.pdf)↓An error occurred and it is not possible to save↓Error detailsAutomatic traceback informationA fatal error has occurred.A traceback has been written to:E:\PTC\working_dir\5\traceback.logPlease send this to technical support.【traceback.log】-------------------------------------------------The trace creation timestamp is: 木 4 17 10:02:31 25The executable build timestamp is: 火 12 11 14:49:32 18The datecode is: 2018400The pro machine type is: x86e_win64The process ID is: 58108The traceback type is : CRASHThe logger exit status is: 00003The Trail is: trail.txt.216The release is: 5.0The product version is: 5.0.3.0The product title is: Creo Parametric-------------------------------------------------Exception EXCEPTION_ACCESS_VIOLATION has occurred in the thread 62488.Main Thread 62488=====================0x00007FF6C25F71F1 NULL (NULL:0) (xtop:0x00007FF6BD110000) ( 0x5c7acd20, 0xddf4e0a8, 0x5c7a7e80, 0xee

try to solve the problem from the professor.

I am using Creo Parametric Release 4.0 and DatecodeM090零件保存提示内存出错，然后崩溃闪退，都是用creo基本功能建的模，请问是否有类似问题，图和处理。