CAD

We tested it from different locations but the license server does'nt work.I am sure that we do not have a problem with the proxy server.Does anyone have the same problem?Question to the PTC folks: Is it possible to fix the problem?

I am using Creo Parametric Release 4.0 and DatecodeM040 When I create the thickness from a quilt, I do not have the special management option exclude surfaces.

Full topic list Want a Mathcad Prime 30-Day Free Trial? Download your copy today. All worksheets created in PTC Mathcad Prime 2.0. Worksheet name   Analyzing Process Capabilities This worksheet using PTC Mathcad takes a normal distribution to represent the amount of products lying outside the tolerance limits. Bearing Capacity and Maximum Load of a Pier This worksheet shows you how to calculate the bearing capacity factor for a specific pier and then uses this calculation to find the maximum load of the pier. Calculating Force on a Truss Connection Joint This worksheet using PTC Mathcad helps you to calculate the force and pressure on a connection joint within the specified dimensions of the joint for a particular material, and under particular trusses and weld lengths. Choosing a Cam-Type Clutch to Drive a Centrifugal Pump This worksheet using PTC Mathcad shows you how to properly choose a cam-type clutch to drive a centrifugal pump. Determining Suction Lift Pump Height

Full topic list Want a Mathcad Prime Free 30-Day Trial? Download your copy today. All worksheets created in PTC Mathcad Prime 2.0. Worksheet name Description Calculating Fault Current Magnitude in Mathcad This worksheet shows you how to compute bus faults on power systems. Most faults in power systems occur at points on the line some distance away from the substation bus. Load Flow Calculations This worksheet using PTC Mathcad shows you how to describe the network for a five-bus power system, using a matrix containing the transmitting and receiving bus numbers, the series impedance, and shunt admittance.  You can also capture shunt data and bus data in matrices. Modeling of SAW Delay Lines This worksheet using shows how you can use Mathcad to model SAW sensors in aerospace vehicles. The lack of support for transcendentals within the Differential Algebraic Equation framework prevents the use of the frequency domain analysis in analog extended Hardware Description Langua

Hi,  Is it possible to download ISO fit tolerance tables from the community, or where can I find the correct format for creating them manually? In my case, the folder is empty.  Thank you!

Currently using Creo 11.  I've found some posts, but no solutions.  Is there a way to automatically show external cosmetic threads in their typical format such as 1/4"-20 instead of 0.250-20?  There was a post from years ago about editing the .hol table, but this method doesn't work as somewhere along the line PTC changed the format of the hole table.  Now in the table, there is only "BASIC_DIA".  If you edit the table to say 1/4 or "1/4", a value of 0 shows up in the hole note.

I am trying to compute the equivalent annual percentage rate (APR) for a series of variable deposits with variable returns.Using the “find” function results in the error message “No solution was found...”. I tried opening up the TOL value, that didn’t help. So I tried the “minerr” function next and a different error message is displayed “Indexed assignment...”, My questions are:Which of the two errors is relevant? Can I solve equations with indexed constraints in a solve block?MP11 file is attached.Thanks for your help,

We're interested in SmartAssembly for a project we have.  It will involve a model using a number of curves generated from .pts tables.  We would want to code both the initial setup, and revisions using new point data.  To do one set, it's simply start the offset points operation, set the coordinate system, browse to the table, then done.  Making the curve is even simpler.  And to update means just edit definition of the pts table, browsing to new, and all that.  Doing it multiple times, it's a couple of simple steps, set within a loop, where the names of the tables increment through a preset sequence (TURN01_V1, TURN01_V2, TURN02_V1, etc).   Question is, does smartassembly have this capability, or more specifically, is that something that can be coded for use in smart assembly?  I am not looking for the code, just some feedback from SA users as to whether we are looking at the right software?

Hi,I have a new server and had to create a new license file for the host.The new license file has “BORROW =1” in all positions. The old license file has “BORROW =720”. If I understand right 720 stands for hours. 720 means 720/24 = 30 days. With the new license file, it is not possible to borrow a license anymore.All licenses are permanent.Is it possible to solve that?

i installed mathcad prime 11 in the computer but the version that i have purchased is mathcad prime 12. I would like to request for the installer for mathcad prime 12

I am using Mathcad Prime Release 9.0 and Datecode9.0.0.0 How would I solve this equation in mathcad: y’=(A’c*l1+A’c*l2+wcb*y’2/2)/(A’c*2+13*y’) where A’c=5.336in2, l1=26in, l2=18in, wcb=13in and y is in inches Tried using the solve block but getting errors saying variable A'c is undefined. Can solve it without units and entering the variables manually but assuming there is a better way.

How can we selectively suppress specific features within a group instead of suppressing the entire group?

Have a good day, community. I have a problem with solving a vector-type equation. The issue is that the solution only returns the last result, ignoring the previous calculations. Could someone please help me? I’m uploading the file in Mathcad Prime V.10. 

Hi,I am trying to plot the average pressure from several monitoring points in Creo Flow Analysis / Creo 12.I have 10 monitoring points namedPoint 01, Point 02, ... Point 10According to the documentation, I understood that monitoring point values can be accessed using syntax like:flow.P@probe."Point01"and that user-defined XY plot variables should be created using:plot.varnameSo I tried defining an expression like:plot.P_avg = (flow.P@probe."Point 01" + [...] + flow.P@probe."Point 10")/10#plot.P_avg: Average Pressure [Pa]However, I cannot find plot.P_avg as a selectable variable in the XY Plot panel or elsewhere afterwards.Has anyone successfully plotted an average value from multiple monitoring points in Creo Flow Analysis?Am I missing a specific place/context where the expression must be created, or is there another syntax required?Thanks in advance.

Hello Team,We are trying to install\upgrade Creo View Express 13.0 as offline installer.As per the installation guide, if Microsoft WebView2 Runtime is already installed on the machine, the installer should detect it and proceed without downloading or modifying the existing installation. However, this is not happening.We have, Microsoft Edge WebView2 Runtime version 148 is already installed on the machine. During Creo View Express 13.0 installation, the installer still attempts to download WebView2 Runtime version 146 from the internet.Since the environment does not have internet access, the installation cannot proceed.We tested both x86 and x64 WebView2 Runtime installations.We also tested installation under system context and administrator context.Test Environment is Windows 11 Virtual machine.Need help on,Is the installer specifically checking for version 146 only, or should newer versions (such as 148) also satisfy the prerequisite?Does the installer require a particular WebView2 c

Hi All,I’m facing an appearance‑related issue when importing STEP AP214 files into Creo 11, and I’m looking for guidance or best practices.Workflow and Issue:I export a STEP file (AP214 format) from Fusion 360. When I import this STEP file into Creo 11 as an assembly, all components appear with the default grey appearance. However, when I clear the assembly‑level appearance in Creo, the original part‑level appearances/colors are restored correctly. The same STEP file opens correctly with appearances intact in Autodesk Inventor, without any manual steps.STEP Schema Used:FILE_SCHEMA (('AUTOMOTIVE_DESIGN { 1 0 10303 214 3 1 1 }'));Questions:Is there a way in Creo 11 to retain the original appearances automatically when importing STEP AP214 assemblies? Is this behavior related to how Creo handles assembly‑level vs part‑level appearances during STEP import? Are there specific STEP import settings, config.pro options, or best practices to prevent Creo from assigning the default grey appearan

Hello Ladies and Getelman, I am a student of the TU-Wien in engenering. I really like the Cad lessons and have great fun creating parts and assemplys with Creo butrecently my licensestoped working. I tryed activating it again with the installation guide providet by the TU but every time i try to put in the licencing Code It just says Error (Fehler!). I asked my proffesors about this and they just sayed that it looks like they can´t do anything and i should figure out a allternative like working on the projekts from a friends PC. But a have a assiment due the 24. and every student got a differnet one so i would have to make everything again with took an entire semester with 4 weekly hours each and many more at home. I don´t know what i can do, maybe i am just to dumb to install a new license. I would really appriciate a repply with a solution to my problem if there is one. Thank you either way for listening to my problem. Thank you again- Matthias Eder

I am using Creo 9.0.8.0 and in the process of obsoleting some parts. I delete a couple of patterns of parts (stacked on a skid), but the quantity dimension is left behind (orphaned?). Is this a bug?   Before deletion (I hadn't saved, so I exited and started over) After deletion Thanks, Dale

for MBD files i’ve made revisions after that i need to clear the notes like {5}, so that is their any way to clear them, i tired by mapkeys or modelcheck but couldn’t get exact way..Pls let me know any possible scenorios Thanks in advance 

HI i dont know who i cant convert the file from xmcd to mcdx. can some kind soul help me to convert it ?

Hello, typically when using derived parts we know beforehand if we will be using them or not. To do this typically we would make the purchased blank, then use the derive (merge inheritance) feature to show the part was made from said blank beforehand. My question is, if we already have an existing part, is there any way we could create a blank, then change the existing part to be derived from said blank?

Hi,Does anyone know how I can change the default window size in Creo?Let me explain better: when I run the command View >>> Windows >>> Default Size,the window shrinks like this.Is there a way to get the screenshot at the maximum screen size or a larger size?Thanks!P.S. I’m using Creo 12.4.3.0

We are using Creo parametric 8.0.8.0. The model of laptop has changed to Dell Pro Max16.There are a lot of unknown issues during Creo operations like sudden shut-down of Creo, taking too long to open assemblies compare to old laptops and so on.Dell Pro Max16 is on Creo parametric PTC Creo 10.0 Hardware Support Dell while it is not on PTC Creo 8.0 Hardware Support Dell. Would there be any potential solutions for this?

Hallo,in einer Baugruppe sollen über “Ansichts-Manager” verschiedene Varianten der Baugruppe erstellt werden. Dabei sind in einer Variante nur jeweils wenige Teile spezifisch, die meisten kommen in allen Varianten vor. Einige dieser Komponenten werden aber an unterschiedlichen Stellen verbaut.Wir kann das realisiert werden, ohne bei jeder Variante diese Komponenten neu in die Baugruppe laden und verbauen zu müssen?Danke und Gruß,Jörg

how can we convert xmcd files if converter is not working, is this a bug any workarounds?