Creo+ and Creo Parametric

Hi everybody. I cannot remove the thread lines where you can see the part have an extrude. The lines from the hole are gone if i remove the thread, but the lines from the thread appear again when turned on.  Hope someone can help

Hi everyone,I am using Creo Parametric Release 10.0 and Datecode10.0.7.0During the replacement of component by an unrelated component, the replace user interface propose to select the corresponding references used in the assembly itself.Does exist a way or a configuration option to detect also the references used in the drawings ?Due to this missing detection, the attaches of the drawing symbols are lost.Gaël

Creo 8:  Well, ain't this peachy.  Got a large assembly in a couple different configurations/Reps (some parts not used in certain Reps), and if you create the dwg view using a Rep, but then change the Rep at the assy level, the BOM will change but the dwg view WILL NOT.  Replacing the Rep for that view, or everything else I tried, DO NOT WORK.  The only thing that worked was DELETING the view, and putting a new General view in it's place. Nice, especially since it's a large assy with a bunch of sheets.  So, my "Pro/WORKAROUND" is to NOT make dwg views until you are 100% sure the Reps won't change.   Must be all that "Enhanced Functionality" PTC keeps crowing about when they waste time giving us confusing new interfaces, but spend zero time fixing bugs...you know, like that "split cylinder" BUG, or the one where threads don't show up in the model except in wireframe viewing mode, or.......   Anyone else run into this issue?

HalloIch habe das Problem, dass 8 Bauteile aus meiner Baugruppe (ca. 50 Teile) nicht mehr geöffnet werden können und in der Baugruppe auch nicht mehr angezeigt werden. Es wurden schon Zeichnungen dazu erstellt, die sich jetzt auch nicht mehr öffnen lassen. Die Teile wurden aber seit einem Monat nicht mehr verändert, oder umbenannt, oder auch anders Referenziert. Wie kann ich die wiederherstellen, ohne das ich wieder von Anfang an beginnen muss? Ich benutze Creo 10 und es wurde alles auf einem USB-Stick gespeichert. Ich habe auch schon alles auf einen anderen USB-Stick kopiert, der aber auch den selben Fehler anzeigt.   

Hi everyone, I'm a fairly new user, but I've been getting comfortable with most of the tools: using sketches, datums, and building surfaces. I've been working on a project and I'm stuck on one part that I’d really appreciate some guidance on. I’m trying to model a back surface (see images below) that has a complex 3D curvature. I initially tried using the Intersect tool, but it didn’t give me the full shape I needed; it only creates sketches at the intersection of two surfaces, and this back surface seems to requires at least three reference surfaces or profiles to fully capture the curvature. I’m trying to approach it using 3D sketches and datums to define guide curves and then generate a surface from those. I’d prefer this more parametric and controlled route over something like the Warp tool. But I haven’t found a clean way to do this yet. The curvature is irregular enough that I’m not sure how to lay out the sketches or organize the build sequence.Has anyone tac

Imported step file of a cable created through the cabling add-in doesn't show up. As in the model of the cable is in the model tree, but doesn't show up in the graphics window. When modifying the original cable by removing locations to simplify the routing and re-exporting to step and importing it, the step file shows up.AP214 is being used. Cable surfaces is selected in export. What breaks the import/export for cables? Can complex geometry or bends break it? 

Why the component (Guide frame) leaves it position while converting .asm to .step to .prt. Purpose is to get all comp in one with no history but right positions. Pl Guide what is making this move.Thanks in advance!

I am using creo object toolkit java to make some secondary developing.Suppose I have get the ComponentPath of a part or component in an assembly model. Which function can I use to hide and unhide the part or check its hidden status. I read the usergudie a thousand times and could not find one. Belows are functions I have tested.com.ptc.pfc.pfcModel.Model.Displaycom.ptc.pfc.pfcSelect.Selection.Displaycom.ptc.wfc.wfcSolid.WSolid.DisplaySolidSadly, none of them help.Does the toolkit provide the function to programmatically hide and unhide part, just like hit the button in this picture?

We are partnering with another shop that has sparse data for converting their dies for machining purposes.  Sometimes we get part models, sometimes dirty geometry die models and sometimes absolutely nothing. In the most recent situation all we have is a scan of the top and bottom dies.  The die impressions themselves don't have any sharp edges, and the radii sometimes wipe out the draft walls.  There would be a combination of revolves, extrudes, lofts and there are locked transitions.  We are tasked with reverse engineering these dies to make parts that size accurately and within a timely matter. I wish that I could share a screenshot of the actual dies but that would be proprietary in nature. I have been told that machining the actual STL is very slow and not very clean. Can you suggest the best way to convert the STL scans into at least sealed, accurate to machine surfaces?  It would be nice to have these parametric, but that would require

In the drawing driving model we have a manual user entry parameter called "Drawn" which is used in the drawing title bock. Per ASME standard this needs to stay as the original (rev -) creator no matter what rev the drawing is changing to in the future.   We tried using part relation to drive the parameter:  drawn=ptc_wm_created_byThis parameter updates every time to the person who created the new revision of the model, hence the title block name changes.    Is there something we can automate that doesn't change like:  drawn=ptc_wm_created_by:revision-    Thank you in advance.

Hi,In the assembly I renamed one part and saved the part and the assembly. Later I converted that assembly into 3d pdf format.  When my client opened the 3d pdf file, and found that old part number only appears in the 3d pdf model tree.  This is getting solved by saving the assembly and closing all the parts & assemblies and session. After that I have to do Erase not displayed to remove all the temp file. Then I opened the creo assembly and converted to 3d pdf. Now it is working fine.

Requesting EMX team to separate "Return pin" from ejector pin category.  The issue is during cleaning up ejector pins using command " delete all ejector pins" , this return pins will also get deleted and need to reassign all the references related to it. kindly check.

但是现在使用的版本号为Croe 12.4.0，映射键F2，为显示/隐藏轴，当映射键F2在组件时可以正常使用;在零件的时候F2就无法使用了，零件状态的时候按F2无任何反应（如果不使用映射键，在快捷键中设置F2也是可以正常使用的）

The Creo Parametric CAD application currently supports drag-and-drop functionality for opening design files directly within the session view area. However, as part of a customization initiative using Creo Toolkit, I am seeking the ability to intercept these drag and drop events when a file is dragged into the Creo Parametric session. At present, there appears to be no API available within the Creo Toolkit that facilitates the interception or handling of these specific events. Upon reaching out to PTC support, I was directed to knowledge article CS230497, which confirms that capturing drag and drop events through the Creo Toolkit is currently not supported. The support team recommended submitting this as a product enhancement idea. Therefore, I’m formally requesting the addition of APIs to the Creo Toolkit that would enable developers to capture and respond to drag-and-drop events within Creo Parametric. I invite fellow community members to vote for this proposal to help

Hello, I'm having troubles using this two funcitons. Effect I'm expecting using this two functions one after each other. I see the same thing without changes by getting actual transformation and applying it to the model. Now let's see what's actually happens let model = pfcGetCurrentSession().GetCurrentModel() let transform = model.GetCurrentViewTransform() model.SetCurrentViewTransform(transform)This code retrieves transformation from opened model and i expect this transformation to be correct because I do actually see it in model and there is no errors in it. But: Uncaught Error: pfcExceptions::XToolkitBadInputs in ProViewMatrixSet at <anonymous>:3:7Is there any extra step needed to repair transformation gained directly from model?

Hi guys.   I have a quick question about simplified reps in drawings. I know you can change the simplified representation for new views in the drawing models sidebar, but I need to know if there is a way to change the representation for already created views. I have a part that was drawn as the master rep, but for a long list of reasons, that iteration of the part is now a simplified representation. Is there a way to keep the drawing the same? In other words, can I change all those views from the master rep, to a simplified rep without deleting and redrawing them all?   Best Regards, Alex

Creo Parametric 8.0 I use OTK JAVA replace session model not find the API..so ...................I want  Model.EraseWithDependencies then session openFilebut ....................some model its success ,some model fail throw XToolkitInUse everyone................you Know how to do replace session model? (physical has new verison but session model is old version)why the Model.EraseWithDependencies throw XToolkitInUse? 

I get really confused about this, it should be as simple to put the font to the load point of the font folder? The one where config.pro points with the pro_font_dir? I have it all set upmagyar_iso30985font.ndxhu_latin_1.fnthu_ascii.fntThe ndx contains the fnt names:hu_ascii.fnthu_latin_1.fntThe font is loaded, but where the hungarian (ő for example) char should be shown, there is only squares like this:  The font is proper, and was working before, any ideas?

Whenever I print to PDF, instead of the file name coming out as the drawing name i instead getthe prefix Creo Parametric - (character that looks like a chessboard), then the file name, then four additional digits.This is not just Adobe, but with other pdf print options too.So each time I save I have to delete this extra detail. which is really annoying and time consuming.But if I save as PDF it screws with text and line thickness.  I can't find where it is pulling this additional detail from, or how to stop it. Thanks in advance if you can help!  

Hi everyone,I’m currently exploring Creo’s multi-axis manufacturing capabilities, specifically for impeller machining. I’ve already programmed and machined an impeller using Creo Multi-Axis, but all the strategies—roughing, blade finishing, and hub machining—had to be created manually. (Please see attached picture.)Other CAM software like Mastercam and Siemens NX offer dedicated modules or toolpaths tailored for impellers and other bladed components.So I’d like to ask:Does Creo offer any specialized tools or modules for 5-axis impeller machining?Are there built-in strategies for blade-to-blade finishing, tool tilting and collision avoidance, and roughing in deep/narrow passages?What about hub finishing with smooth transitions?Or is everything expected to be built manually through generic multi-axis features?I’d appreciate input from anyone who has experience machining turbomachinery parts in Creo.Thanks in advance!

Hi, I'm using Creo Parametric version 10.0.3.0. I have a couple of questions related to plug-ins:Is the SubD plug-in available for Creo Parametric?Is there any difference between Freestyle and SubD

Hello,I have created a small C++/CLI library which make calls to a C# DLL, this library works fine if I call it from any other C++ project, but it does not work if I call it from my Toolkit application (based on Creo Toolkit 10.0.6.0).The application compiles and links fine, but it fails to start from the Auxiliary Applications menu:  Checking that trailfile info, I only can see these lines related to my app not saying any clue about the possible root cause error:  What I'm thinking is that Creo doesn't support Toolkit apps involved with C++/CLI code, but I would like to confirm that, do some of you have experience this? Thanks.       

Profile Milling with Tool Compensation and Ramp Entry or helical for Internal Profile Hello CREO Users,I am working on a milling operation for an internal profile (similar to a valve seat geometry) in Creo Manufacturing. My objective is to machine the internal contour using tool radius compensation (CUTCOM) and to ensure smooth ramp transitions between Z-level passes or using helical folling the profile to avoid marks on the final surface.I have tried the following approaches:The Cut Line strategy allows helical movements and smooth transitions between passes, but it does not support tool radius compensation (CUTCOM). This is a requirement for my process.The Profile Milling strategy does support CUTCOM, but it does not offer ramp or spiral entry between Z-level cuts. As a result, the tool plunges vertically at each level, which causes unwanted marks and steps in the internal diameter of the part.I've tried to explore all the SCAN_TYPE parameters. LEAD_IN and LEAD_OUT approach but

Hi! i've installed creo view express but i can't get it to work, i dont get any error message, it just does not open.    

Hello, I am trying to make a fix for a turbine with some complex geometry in Creo 10.0. I don't want to just sketch a shape and extrude it, but rather I am trying to get it to follow a curve. This feels like it should be easy, but I am struggling with it. This is the shape and that is the type of curve I want it to follow. What is the best way to accomplish this.