CAD

I am using Creo Parametric Release 6.0 and Datecode6.0.6.0Problem with solid center line showing up in a drawing view. Its a offset section with a sketch where there is two lines in 90 degree The section is showed by a full unfold, partial view.Not sure if this is suppose to look like this or if its a bug or if there is any detail settings to hide the solid line that goes through the hole feature?

I want my Mathcad Prime 3.0 sheet to auto populate using a different unit than the default unit system. For example I want all my answers to be in mm (millimeters) instead of m (meters). Can I change the default so I don't have to type "mm" into every answer manually?Thanks

Dear, How to prepare the nozzle reinforcing pad in creo (refer the attached sketch) dimensionsShell OD - 3000mm x 12 thknozzle od -  1067 mm x 12 thkR.F pad OD - 2000 x 12 thk please provide the step procedure Regards,Robert   

Is there a known explanation for the next? I would think that the resulting units should be the same, but apparently not.This was with Prime 7.

Using Creo 7.0 as of today, I use the dark per-Wildfire dark background, the sketcher constraints appear black on the dark background, they appear light colored when I hover over them, is that the intent?  Sketcher appearance is grayed out so I'm unable to change the constraint color.  Is PTC trying to force people to use the default/light background???

Hi,   Can we use a specific parameter to control whether another parameter is designated or not? Linked to topic - https://community.ptc.com/t5/3D-Part-Assembly-Design/Unchecking-Designate-parameters/m-p/754245#M121251   Appreciate your help.  

I have a very simple problem as you can see below (file attached too.) I'd like to fit a line to measured data. There's something fundamental about minimize (and solving in general) that I don't understand and can't seem to find by searching through the literature. Changing TOL and CTOL have no effect. Help?  

Is there a way to "read" the *.ui file to understand what UI customization is applied? Unlike config.pro that can be edit/read via text editor, the *.ui file could not be read/edit via text editor like notepad Basically, what i am trying to achieve is to "read" the customization that is applied via the *.ui file  

Two questions. When the Designate box for a parameter is checked, it would mean that the parameter is visible in a PDM system. I understand this, but it doesn't apply to me as I don't use a PDM software. The second purpose, according to CREO Fundamentals, is (and I quote) to "make the part level feature or geometry level designated parameters appear as a component in an assembly BOM".I'm not sure what this is supposed to mean, because I believe this implies that you can't use undesignated parameters in a BOM table? Which can't be true, because I definitely have undesignated parameters linked in tables (in drawings for instance). Could someone shed some light on this? And lastly, what advantages are there to NOT designate a parameter?

Hello Everyone.How to write a symbolic evaluate Determinant code ?Thanks in advance for your time and help.Best Regards.Loi.

How do I get Mathcad Prime to give me colored coded results. If the result is Pass, return color in Green and if fails, Red? Please help  

When using Submatrix, is there a shortcut to specify the end of the column or end of the row?    

files created with MCAD 14 or MCAD 15 can be opened in MCAD 14, saved and re-opened in MCAD 15? 

I've got an OTK JAVA Free app working to create simplified reps with a method as shown below. I cannot get Creo to show any components in this simplified rep.The method should accept inputs as a Solid (the assembly that the simp rep is to be a member of), an integer sequence (I only want to show a single component, so only the index 0 is used) and an integer (only used for messages, denotes it's location in a sequence). The method should create a new simp rep with the default action to exclude all components, which it does successfully. It should then add the component with the feature number that is index 0 in the integer sequence as a master rep. This does not happen. So my question is, what should I do to the below code to make the component identified in the "is" integer sequence as index 0 appear as a master rep in the simp rep called leafsimp? At the moment I just get a simp rep with all components excluded. In the below, printMsg is a method that just calls System

I've found the series of videos for Creo Ansys, which are somewhat helpful, and I took the half day class for Creo Ansys as well.  However, I want to take a deeper dive into the various types of joints to better  understand how they function. For Creo Simulate, there are tutorials from PTC that you complete at your own pace. There are downloadable files for these tutorials so you can actually perform the tasks instead of just watching someone else do it. I haven't been able to find these types of tutorials for Creo Ansys. Does anyone know where I can find this kind of self-pace training for Creo Ansys?

I am using Creo Schematics Release 9.0 and Datecode 0.0.0How is Schematics 9.0 integrated into Windchill. The WWGM 12.1.1.1 does not offer Schematics 9.0 as an application.

I am setting up a simple beam bending simulation of a simply supported L channel.  its 3x2x.025.  It is 24" long and 2 equally spaced load of 25000# each.  When I verify my results using the bending equations I am way off.  Can anyone suggest what is going on?   

Referring to CS80656, I want to convert a quilt surface to STL, but for curved surfaces (mirrors) it behaves like overlapping points. How can I avoid it?  

Hi,I'm starting to evaluate the Design Exploration Extension, for now I find it interesting but perhaps too limiting.Anyway, the question is: Is it possible to rename a Design Exploration session?Thank you.P.S. I use Creo 9.0.2.0 

I am using Creo Parametric Release 6.0 and Datecode6.0.3.0Hi Team, The bitmap image is attached in a drawing as an object but after check-in, it's not showing in creo view, and after checkout same drawing in creo its also not visible in creo.

Trying to plot a spring constant after measuring deformation due to applied weight Why is this scatterplot not working? Both M and S8mm have 10 values    

Often, when working on parts, especially in assemblies, I'd like to view dims from multiple features - at the same time.  Or both feature and assembly dims.  I can't find a way, so I'm hoping you know about another bit that PTC hid away. Coming from an older version, this is maddening.  I feel like I am licenced to fly and F15 but only allowed in the Cessna 150. I have resorted to working with a pad of paper so I can write down dims from all the desired features and assembly positions, so I can at least be partially productive.  This is especially useful when looking for minor interferences when there is a stack up - and for making similar changes in many features or parts.  I don't even see a way to see all the dims from one feature with 2 sketches like a sweep. Please tell me I'm missing the obvious.  Thanks.

Hi All,I would like to create a Mapkey that not only creates a STEP file, but also renames it. To further complicate this, I would like to pull parameters both from the part as well as the drawing of the part.Format would be as such:(part number)STEP_(drawing number)REV(drawing revision)Where the part number would be pulled form the part parameters, and the drawing number and revision would be pulled from the drawing parameters. Am i crazy? I realize I'm going to need some sort of external .bat file to run various commands, but I'm not sure where to start. Any help would be appreciated.Currently using CREO 4 M150 and Windchill 11. 

Good evening! There was such a problem.I'm a student. I have MathCAD Prime 8.0.0 installed. I used the trial version, and unfortunately it ended. It turns out that I need to purchase the paid version, right? And there is another problem, I'll be honest, to use this program, I created a new account every time. Now, when I receive a trial version, namely a license, a window pops up that I have received the maximum number of licenses for this program. What should I do?

The collapsed area contains the function NumberGenerator() that produces a new number for every supplied (integer) number. Three results are shown. Your task is to come up with a/the definition of the function such that it computes the (correct) value associated with 433 (and any other number in Z).   As you will find out, I've limited the function to just the three first input numbers with: Where the red placeholder should contain the code to implement the actual functionality. To not spoil the fun for others, I'll accept solutions in Prime or Mathcad as either one of: - the function NumberGenerator(), limited to the same input range, in a collapsed locked area, dated later than the timestamp above. The password should be the result of NumberGenerator(pw), and pw is supplied along. - submitted to me in a PM (in case you're limited to express).   Success!Luc