Creo Elements Direct

How do i get a license.conf file? All i can manage to get is lm text files.   

Hello all,        I'm trying to emboss text on a cylinder in Creo Elements Express.  I do the following:   1) Create cylinder 2) Create workplane parallel to cylinder face 3) "Modeling->Modify 2D->Text to Profile" the text onto the workplane 4) "3D Geometry->3D Curve->Wrap on Surf" the text onto the cylinder        ...At this point I can use "Modeling->Modify 3D->Pull" to emboss the text, but it embosses linearly, as opposed to embossing out relative to the surface of the cylinder.  I suspect I should be using "Modeling->Modify 3D->Offset", but I can't figure out which set of options (if any) can accomplish this.         Any ideas?         -BW

I have multiple closed sketches on a body. There are thousands of these sketches. I would like to create separate  parts or features from these closed loops . What would be the fastest way besides Creo Toolkit.

have a busy hole pattern, using Show Model Annotations I am adding the datum axes, but they are too big and overlapping. How do you change the size of when they are first added? (I know how to change them manually once they are added).

Hi All,I have change threaded hole dia standarts. Can I change?I have looked under sd_customize folder full path is "C:\Program Files\PTC\Creo Elements\Direct Modeling 20.5.1.0\personality\sd_customize\MachiningAdvisor" but I did not see all parameters.

I am finding that some edges on a simple rectilinear model will accept a round of say .125 radius on a 4 inch side, show the geometry but not remove the model material which would be gone if the round completed. I've tried starting with different simple models and it fails on some and not others. There may be a common origin of the trick edges like they are edges created by an extrude.  I haven't gotten to sorting this out. I've been running Creo and Pro/e for a very long time and have never encountered this before.   What would you look at assuming this isn't a bug?  

Hello to everybody, I need to import a 2D drawing (DWG format) with made with several "page".To achieve this result, I set ReadAllLayoutData ON and SideBySideLayoutView ON in DXFDWG.conf file. When I load the file start the conversion that requires a lot of time (in  the drawing there are some geometry but many texts).The file size is 71MB!In the end, all 'pages' are imported correctly but, surprisingly, all texts are converted into geometry!The texts in the original file are "text" not geometry. Any suggestions?Thanks in advance. I tried with ME10 20.5.1 and ME10 19 M070 with same result.

Hi all; When I want to save dwg file from annotation module, I am taking following error;"am_save_sheet_dwg/f2_core/unknown_error".  I need help, thank you very much   

Hi community, We have a drawing template for our company which looks like this. The BOM table and Revision table are currently part of the template itself.  Recently we released a new version of format. Upon changing the format to latest format for existing drawings some users faced some issue with Revision table (the lines of older table did not exactly match with new table). Post this problem now we are evaluating whether to keep BOM and Revision table as part of drawing template or add them as separate tables What is your opinion on this?How do other companies handle new format rollout? Any response would be appreciated Thanks in advance Regards,Prasad 

Ignore the comment annotations. Edge opens PDF fine and looks good. Adobe looks like this poor quality below. How would you describe this issue so I can google a solution? anyone know the fix to render right?

HELLO IS IT POSSIBLE TO MAKE AN UNDERLINED TEXT IN ANNOTATION AS ON WORD? THANK YOU EXEMPLE :  ESSAI

Hi, I am currently planning the transition to the latest Creo version for our NC programmers. With that we need to update our client hardware. Since I am not that familiar with Creo I was hoping somebody could give me some insights on the recommended hardware for our clients. e.g.- Intel i5 or Intel i7 CPU?- How much RAM is enough RAM (32GB)?- Do I need a dedicated GPU, if so is a T600 4GB sufficient or should I go for T1000 8GB? Thank you very much for your help.

How can I create a hole table in Creo Elements/Direct? I can't figure it out 😞 I'm a solid works user, so I'm flying blind.    

Hi,in version 20.1 I can install software in silent mode using (for example) this string for 2DAccess : ".\2D_CAD\2D_Access_x64\2DAccess.exe /s /v" /qb! INSTALLDIR=\"C:\CAD\PTC\2DAccess\" MELS=127.0.0.1" and this for Modoeling"./3 - Modeling\20.1.4.0\3D CAD\Modeling (x64)\setup.exe" /s /v"/qb INSTALLDIR=\"C:\CAD\PTC\Creo Elements\Direct Modeling 20.1\" MELS=\"xxxx.xxx.xxx\" ADDDEFAULT=\"BASE,IKIT,BINNT,PERS,RENDER,THUMVIEW,L10N_IT,L10N_ES,L10N_DE,HELP_EN,HELP_IT,HELP_ES\" " In vesion 20.5 this not work.Therei is a way to pass installation parameters in the new versions ?Thanks a lot   

It appears I misposted this in the parametric forum...I hope this is the correct forum now. Cocreate ME10 is Cocreate Drafting, no? I do systems support for users who use Cocreate and I occasionally have to help them when ME10 reports a 'segmentation fault' when opening a file. The error is pretty much always due to a value having been written out which cannot be read back in by ME10, "-1#CNAM" is a common one but I've also seen decimals being written out with comma separation rather than dot separation. We are in spain, so the local decimal separator is comma rather than dot (i.e 1,2 rather than 1.2) but that particular error only occurs occasionally. I'd like to know if there is a either- a command line tool for validating ME10 files, which I could use to bulk identify files which have errors.- or a tool which identifies the line number of the block which is causing a problem instead of the useless 'segmentation fault' which is displayed to the user. We have thous

Dear all, KE Tools version 6.0 contains a new macro with which calculations can be done with the texts of a drafting. The example of the pneumatic cylinder shows the calculation of the consumption of compressed air with the bore, the rod diametre and the stoke: To be downloaded from http://kotom.eng.free.fr/

Hi, where I can download tha latest version ? I have 20.1 but I can't find 20.5 (if it exist) Thanks a lot

Hello,We have large harness with about 250 wires. We designed it with using logical data from Creo Schematics.And we have problem with four wires. They are don't shown in model tree and simultaniously don't shown as unrouted. Some segments of them appear in graphics window, I try to remove them but it doesn't work.I attached screenshot from Compare List - these wires have mismathcing but I don't know why.

I'm trying to set a default text linespace in Annotation (19.0) but it doesn't work the way I try to configure the value. I use the following textstyle configuration. I can change Font and Color but the Linespace does not change.   (oli:sd-set-setting-values :application "Annotation" :style-path "Annotation/General/TextStyle" :style :STANDARD :title "Standard" :values '("Font" "arial" "Color" 16776960 "Linespace" 1.3 ) )  Should this be working this way or should linespacing be set somewhere else?

Hi Team,   I'm new to CREO. Working with HP. I wanted to run a command from windows command line to convert .mi files into .pdf file.  Could you please share the steps or documentation with examples.   Thanks, Som.

There is no mirror feature command

Nx has centering options with two faces of fixing and two faces of centering(moving) faces. So it is very simple to center a body between two other body

When i select the infinite horizontal construction line from the ribbon, the construction line automatically snaps on the part edges as you can see in the 1st pic bellow. But when i add a shortcut for the construction lines, and select the same command, the line doesn't snaps anymore (2nd pic bellow). I don't know if someone can help me, I'm new at this software .     Thanks.  

Im modeling some chunks to export in .stp to mastercam. Can i set the origin  in creo elements/direct, so when i export my chunk to mastercam i allready have my "zero point" where i want?   Thanks 

I need to pattern an identity plate. This plate has a number on itself. It is very difficult to write geometry text, orientate and extrude one by one. Is there an easy way to change text inside the geometry?