Mathcad

Hi,In electronics, we use an operator for the parallel connection of resistors. For example: R1 || R2 which means (R1*R2)/(R1+R2). How is it possible to create an operator like this so that I can use it just like basic operators such as /+ * ?

Hello Mathcadeers,I could not find a way to properly set the Legend on "Chart Component". The legend only shows "1" and "2". Can I set it up to show the actual name; eg PN_Total_ADF4194 and etc? Regards,Ak 

I need to ask about the possibility that Mathcad will allow me to process images through the image processing function, taken with a digital camera, to give me % failure of adhesion of a film on the material in attached image. Can I use Mathcad for basic matrix operations? Or how can I achieve this ? 

Cant install mathcad at all because there is nothing at application selection on setup

I tried to convert old mathcad file but the following error pops up ( I have a Mathcad prime 7 installed)I also have enabeled the .Net Framewor....on my windows, but I still have the same error after that as well. I really nedd the files for my PhD project. Can someone help me with this issue please. Ican also upload the file so that you can help me converting the file. Thank you Tadele 

Hi All,I have an older version of PTC software.It is Prime 2.0.This does all my needs.I had to re-install it recently because it was hanging up or closing down while it was uploading.Just days before it did an automatic online license check, and it passed.I had Prime 2.0 for several years since it first came out.On attempting to re-install its failing to do so.Message is about a component was not installed.The screenshot is attached (Error2).I have installed WindChill....software.I direct the browser to the license file (single user).The install continues and then stop with this message.Error 1935 An error occurred during the installation of assembly component.Next a file name in brackets [.......].Followed by HRESULT:0x80073712.That is the information I have on my failed install.I will appreciate any and all help you have to get me back on with Prime 2.0.PS: The first error is indicated in file name Errorr.The 2nd error the most recent re-install error details provided above is in fil

Hi there , I need to create this table using programingI wrote this program , but it doesn't give me the answer I want: What I wrote in the program is if the bottom value is between z and d .....> the layer is drained and use the angle (alfa) if the bottom is greater than d and smaller than z ....> the layer is partially drained and use the angle (alfa) otherwise write the layer is not drained  I need the answer two have 3 columns1# ( layer ( drained-partially- not drained)2# the angle if it is  drained or partially drained .. if not drained show zero 3# if it is possible this column as well which is the layer kind it is in the table in the sheet as input Thanks Yusra The sheet is attached prime 10

Hello everyone!I have been creating with Mathcad 15, worksheets for the analysis of electrical networks stored in a particular folder for a long time. When I need to study a particular electrical network, I scroll through a file in which there is a list of all the networks studied with the images of the relative circuits. Each of them is called with a hyperlink. So I find this instruction very useful. Is it also available in Prime 10? I would be tempted to buy it if there was such an instruction.

I typically do all my work in a textbox and recently I cannot copy equations and text together and paste below inside the textbox. I would do this all the time but now it doesn't work. I can copy from a textbox and paste outside the text box, but this is inconvenient. Anyone have any insight into why this may be happening now?  Thanks. 

Hello Mathcadeers,I am trying to polynomial curve fitting, but could not find any good example on how to do it.let say I have the following. How do I create a function y1(x1)? Seems Mathcad function "polyfit" function is not the right one.Thanks.  Regards,Ak 

I am using Mathcad Prime Release 10.0 and Datecode10.0.1.0  The new license file cannot be retrieved.--------------------------------------------------Translated text from German to English using Google TranslateBody - Die neuen Lizenzdatei kann nicht abgerufen werden.- By Community Moderation Team--------------------------------------------------

I need a new trial license for my studies   Translated by the Community Moderation using Google Translate.    Brauche eine neue Trial Lizenz für mein Studium

Hello,I actually want to plot an if function for a certain range of numbers. I have tried to generate the values via a loop, but it just won't run.I actually want to plot the if function for values between 0 and 1.I'm sure it's quite simple, but somehow I'm stuck.Best regards and many thanks

HiI just started in calculating on transformers, and i have the problem i cant get Mathcad to calculate in VA (volt*amp) I've searched the net sadly without any results.I also have the same problem with a method to get the right results for VAR.S = VAP = WQ = VARI've tried to use the attached document, but i still only gets it out in W (watts)Hope someone can help me out, because i've soon given up.RegardsRasmus Skjøtt

HOW CAN I DOWNLOAD MATHCAD?I AM TRYING TO GET THE LINK FOR A LONG TIME

I tried to convert old mathcad file but an error pops up ( I have a Mathcad prime 7 installed)I also have enabeled the .Net Framewor....on my windows, but I still have the same error after that as well. I really nedd the files for my PhD project. Can someone help me with converting the old mathcad file to mathcad prime 7 file? Thank you Tadele 

I need to convert a file, but I'm concerned about not being able to convert the hundreds of old files that I have as well.When I tried to convert the file, I got this error message.I've verified that the framework in installed.  I've uninstalled it and reinstalled it.I've rebooted the computer, ran updates, and rebooted again.  I still get the same error message. I assume a security update has broken something, but I'd really like to get the capability back.  

Hi,I created the attached sheet to generate a histogram using the chart component.If anyone has suggestions for shorter code to achieve this or notices any errors in mine, I would greatly appreciate your feedback.

working with Prime 10.  I have two lists with different type of tubular threads.  Using the first combo box select between the two list to pull data from.  Automatically populating the second combo box with available tubing size.  Then auto populated the next combo box with available weights.  If not with a combo box can this be done with a list box?  Pulling from a data table and not having to load all the data within a script editor?  

Hello Mathcadeers,Been using MP10 for the last few days/weeks, and these are the thing that I hope Mathcad can improve to make prime faster. Hopefully MATHCAD designer/project lead/project manager is in this PTC Community. 1. Let say I want to add + in the equation below. In M15, I just need to hit SPACEbar once, and I can add +. In MP10, I have to hit SPACEbar twice. I could use RIGHT arrow button in MP10, but it is not quite ergonomic and RIGHT arrow button is far away.  2. Zoom in and Zoom out is laggy. There is about 1s delay. If the delay can be set to 0s, that would be awesome.  3. There is no option to UNDOCK the menu in MP10. In M15, you can undock the function so that it is always open. In M15, say I do Programming, I can Add Line, do if, assign value <-, do for, with just 4 mouse click. With MP10, it will take 8 mouse clicks. Would be good if Mathcad Prime can have the option to UNDOCK menu.  4. Not many options with Right Click. For exam

Hello Mathcadeers,I am designing a phase lock loop circuit (electrical engineering) and trying to use Mathcad Prime 10. I got stuck, as Mathcad Prime 10 could not find the solution. I used to be able to solve this, with no problem in Mathcad15.The program is to find the cross section (on the x-axis) of the DARK and the RED traces, where Fout1 is a variable. Attached is the MP10 file. For illustration, I set Fout1 to sweep from 3.5Ghz to 12.5Ghz, 1Ghz step. It takes really long (really long) to find the solution. If Fout1 has 3 points, then takes few minutes. If Fout1 is say 10points, it probably won't be able to find the solution. In Mathcad15, it takes 2 or 3 seconds. Attached is the file, in case anyone want to take a a look.  Regards,Ak      

Hello,I can not find the result. Example11 is my sheet it should be like in the file example22.regards,

I have to use Matcad on one of the modules of the university course i am doing. I went to purchase the student license and it states that the estore is undergoing maintenance but it will provide me with prime 10 free for 30 days. So i was emailed a link, downlaoded prime 10 and then after being told i had to create two accounts, one on the web and one on the app it eventually got the license and full functionality. I then get an email stating my trial is running out and to click the link tp purchase a student account. I click it and it asks me to enter details and someone will contact me. This has been over 2 weeks now and multiple forms filled in for contact have been ignored and no one has contacted me so i can purchase a student license. I am at a loss. ALl i want to do is keep MatchCAD going for more then 30 days as the module is 3 months long! BUt for some reason PTC seem impossible to actually purchase their product.Does anyone know how i can purchase this license or how I can ma

I have a permanent floating license for an older version.  Although I have the license files, I no longer have the Flexnet server files (for LINUX) to serve the license.   Can anyone help with the Flexnet server files?

Hello,Why does PTC Mathcad Prime seem more oriented towards CIVIL and MECHANICAL Engineering, and much less towards Electrical Engineering, and Physics, and more in depth Mathematics? Will this be the case in the future?