Mathcad

I can't install the ptc mathcad again after deleting it by mistake

study

It is a sinusoid: Is it a sinusoid or this curve has any other name? I will not sleep until I get an answer!

Mathcad Prime 6.0 xmcd, mcd converter fails to covert files created with Mathcad 14.

What would cause the "watertemp" not to graph? I implemented the same steps for I(t) as I did with Ta but the water temp on the graph remains a straight line.

What causes a vanishing_step_size error? I've tried searching the forums and through PTC support with no luck. I am receiving the error when trying to use Odesolve in the solve block.

Please, can one help me and send Maximum Product Space Method in Mathcad codes for any probability distribution Thank you

Calculation only with symbolic Math!

I downloaded Mathcad prime 5.0 via the link provided after purchase. When I doubleclick setup.exe (after unpacking), I got prompt "Do you want to allow changes to your disc?", I press "Yes" and the window closes and nothing happens. I have Win 10 and MS framework installed. Any advice?

no file

Hello Dear Friends,How can I implement a Smith Chart in Mathcad 15?Is there an example of a Mathcad 15 file that described this kind of implementation of this Smith Chart?Thank you.Best regards.

i loaded Mathcad express but my license has expired. I thought express was a live time. How can I get a license that lasts more than a month?

Hi,   I have a problem that i hope someone here have a solution for - see below (also attached).  

Hi,   Trying to use Mathcad for the first time to optimise a heatsink. Trying to find hL in the screenshot below, it's units should be W/m^2*K, any idea why it's breaking down to kg/s^3*K? Any help would be greatly appreciated.   

This is a very elementary question, but I cannot find a solution. I have two columns of numbers, the first (angles) goes from 0 to 90 in steps of 10, but I plot them in radians. The second  column is the measurement result at each angle, i.e. 10 values, the first being zero and the others are negative values down to -21. When I try to make a polar plot, I get the measurement values plotted in the 240 to 270 degree sector, and the radial axis goes from 0 in the centre to +21 at the perimeter. If I try plotting in degrees, I get a bizarre scatter plot over the whole circle, but only 7 points are plotted. How can I plot these data correctly?

Hi, I bought a book called Thermal Engineering Studies with Excel, Mathcad, and Internet, and I replicated a problem in chapter 1.    I wondered if someone can point out what I am doing wrong because I'm not getting the answer. The message that I get is that the value must be a scalar or matrix.    I also attached the file I was working on in Mathcad Prime 3.1.   Thanks! 

I downloaded Mathcad prime 5.0 via the link provided after purchase. When I doubleclick setup.exe (after unpacking), I got prompt "Do you want to allow changes to your disc?", I press "Yes" and the window closes and nothing happens. I have Win 10 and MS framework installed. Any advice?

I'm trying to install Mathcad Express by opening the installation file pim_installmgr_mathcad.exe that I downloaded from the ptc website, but this doesn't work. What should I do to make it work?

Using Mathcad 15 to do curve fitting of measured data. It's pretty tedious to down-select a subset of the data, analyze it and publish the results. over-and-over-and-over again (e.g. every time the test laboratory runs a new test).  Wondering if there's a faster way.   I'm using the Excel Component rather than File Input (or other means of getting external data into Mathcad).   I have a bunch of test data in Excel. Every test is stored in a different file.  Every file has different numbers of rows.  Inside the data are several events.  I'm only interested in doing data analysis between two specific events. Meaning the size of the data I'm interested in and its location in the file is variable every time the test is run.   My work flow looks something like this: Excel save-a-copy of my pre-processing / post processing template. Copy / paste the data from the test lab's Excel file into my template. Inspect the template for the measurements that indica

Testen

Trying to Activate with the Key file that you emailed me, but it will do nothing after browsing to the license key location on my computer. I selected the product to be activate and all I have is the screen that says Done, the following products has been licensed (PTC Mathcad Prime 6.0.0.0), and my only choice is to Exit. if I do Exit, it still says 28 days left or less days.

I tried to start Mathcad 15 and it gave me a license error. Specifically the host of the system doesn't match the host id of the license file. I'm using Windows 7 and haven't started Mathcad in several months. I'm on a laptop and recently switched to a new wifi router. That, along with any software updates is the only thing on the computer to change since the last time I ran Mathcad. The license path in the popup has my correct license path info and gives a flexnet licese error of -9,57If i use the license wizard to configure the license for use it says the selected license has been installed and Mathcad licensing has been configured to use it, but it still won't work.To quote King Arthur in Monty Python and the Holy Grail, Any help you could give me would be helpful.Jim Petty

Hi everyone.   Im new to using MathCAD and i suddenty can't open my file.    It says my file is corrupted? This is the message i get:   Does anyone knows how I can fix my file? Or maybe even fix it for me? 🙂   I have attached the file - hope you guys can help me, thanks

Здравствуйте. При установке сервера лицензирования возникла проблема. После установки программа не может прочитать файл лицензии  Пожалуйста, помогите решить эту проблему  

I have downloaded the trial version of Mathcad 15, bought a single user new license. PTC setup is running for a long time, but it seems like it is hanged at 75% installation progress......how long it takes to complete the installation? What should I do? Should I cancel the installation, and restart setup again? Thank you, Hawal