Mathcad

plese give me the steps and attech your solved file

My students (Занятие 2. Анимация двери автобуса) have animated a bus door.See please the video and the attach. Video Link : 6372 But what is this part of the trajectory of the point 3?

Thermal Engineering studies with Excel, Mathcad and Internet

Once I add units to the variable, the plot value is off by 386. If I change the units to lb/in^2 the result is correct. However, the units for pressure are NOT lb mass. I tweaked settings in Tools/Worksheet Options but I have not found the correct combination.What did I miss?

Hi all,I was seeing some strange inconsistencies between sheets when attempting to evaluate expressions symbolically.  After some time I traced the inconsistency back to the "point" shown in the attached sheet.The attached sheet shows what I expect to see.  After evaluating a function and assigning the result to a variable, the symbolic evaluation shows the result.However, in a different worksheet, I see the following:For some reason, Mathcad is presenting the result as the original function.  I'll post the problem sheet if necessary, but as you can see here, Mathcad has already found a numeric solution and assigned it to a variable, and has even managed to display it when called up again.  But when I use the symbolic evaluation on it, it brings up the whole function.  But in the attached worksheet, it does not.Any ideas why this happens?  Or at least, why the difference between worksheets?Any advice is greatly appreciated.

Can anyone help me to format the result to say 2 decimal places?Thanks

Use an appropriate function using Mathcad to find the remainder when12345678981129 is divided by 5518.Can anybody help in this?Beginner in Mathcad...

HelloI tried installing on my new computer PTC Mathcad Prime 3.1 on win 8.1I went through installation and all went fine and it's said it completedbut when i searched for the software it wasn't exists on start->apps and also add/remove software.only the diagnostic tool was installed.when i searched for it on hard-disk i found folder in program files PTC\Mathcad Prime 3.1 but it contain only one file mathcad.p.xml under PTC\Mathcad Prime 3.1\bin\pim\xmlso i tried reinstall but the installation software said that everything is already installed and suggested only to "update from M030"I proceed with the so called update which finished successfully but again the software cannot be found.maybe i should delete all file related and registery but i wanna be sure i dont do any harmsomebody have a suggestion how to do fresh install?thank you,אור הירשפלדOr HirshfeldMechatronic EngineerSK- Electronikail.linkedin.com/in/orhirshfeld

Hi,I recently open the download section on PTC's site (link: https://support.ptc.com/appserver/auth/it/esd/product.jsp?prodFamily=MCD ) and see the following message:"VERY IMPORTANT: Critical issues with Mathcad 15.0 M040 in handling matrices with 256 or more elements. Please refer to CS218119 - Warning: an unrecoverable read error has occurred. xx regions could not be read from this document while opening specific worksheets in Mathcad 15.0 M040: http://support.ptc.com/appserver/cs/view/solution.jsp?n=CS218119CS217297 - Error "Operation aborted: max-element-depth constraint violated" occurs when evaluating big matrices in Mathcad 15.0 M040: http://support.ptc.com/appserver/cs/view/solution.jsp?n=CS217297 PTC will release a new maintenance release Mathcad 15.0 M045 that would address these issues soon."

We’ve recently found, through customer reports and our own testing, an issue with matrix definition and evaluation that was introduced in PTC Mathcad 15.0 M040. This issue affects matrices of 256 elements or larger and can lead to a failure to evaluate and the possible loss (if document is saved after failure to evaluate) of matrix definition regions themselves. This tech support bulletin has more information on this issue. We intend to release PTC Mathcad 15.0 M045 as quickly as possible which will include a fix for this issue. The release date for PTC Mathcad 15.0 M045 will be posted on the Product Calendar page soon.

Hi...how can I use  API to make a interface application (look like a clip in PTC Mathcad | Engineering Calculations Software

Hello everyone.I made the following function in VBA (Excel) to retrieve the value of the variable B from the mathcad file using the API.The Variable is defined in the file with a unit i.e. B := 2 mPublic Function test2() As Double    Dim objApp As Ptc_MathcadPrime_Automation.Application    Set objApp = New Ptc_MathcadPrime_Automation.Application           Dim b As Ptc_MathcadPrime_Automation.WorksheetReadonlyOptions    Set b = objApp.CreateWorksheetReadonlyOptions    bb = b.SetOptionValue(WorksheetReadonlyOptionNames_RequestToUpdateInputsEnabled, 2)        Dim objCalc As Ptc_MathcadPrime_Automation.IMathcadPrimeWorksheet3    Set objCalc = objApp.OpenEx("C:\Users\kai.jakob\Desktop\Testo.mcdx", b)    Dim a As Ptc_MathcadPrime_Automation.IMathcadPrimeOutputResult    Set a = objCalc.OutputGetRealValue("(@LABEL VARIABL

Примеры здесьKinematic models in Mathcadи здесьDynamic models in Mathcad

Hi All,I currently have run into a small issue with the way that Mathcad displays the unit system when using the explicit command. The default in-built unit system defines a Force * Distance as joule rather than a moment which is what I want. To avoid having to change from joules to moments (N*m) every time I calculate the capacity of a beam I have created a custom unit system which defaults force * m to kN*m. However, as you will see below when I call on a result that is calculated earlier in the mathcad sheet with the explicit function it will cause unnecessary unit conversations (see 1x10^4 / 1/x10^3). Is there a way of controlling the units in the situation? I am keen to find a solution for this as it complicates the calculation for the person reviewing the work.FYI I have a mathcad prime 3.0 so if there is a solution with this version I will happily switch.See below attached images:Kind Regards,Liam

Dear experts, I'm a third year Agronomy major from Costa Rica. I'm calculating degree days built up for every day in a given data set with over 7 000 observations. Each observation is an hourly average so 24 observations make for 1 day. There are around 300 days in my data set. Growing Degree Days is a measure of acumulated energy in a system during 1 day and it is calculated as follows:Max T = Highest temperature measured from 0000 to 2400; Min T = Lowest temperature measured from 0000 to 2400; Tbase = Minimum temperature required for crop growth (specified by literature)GDD = (Max T - Min T)/2 - TbaseSo, what I want to do is grab my data set, split it into 300 or so chunks of 24 observations. Out of those 24 observations I need to calculate the maximum and the minimum. With those values determined I can now calculate GDD. I need the algorithm to store that value in a matrix and move to the next 24 observations. If the first day is from obs 0(start) to obs 23(end), the second day is f

Hello,How do I start Mathcad from c#? Try to create a new object of type Ptc.MathcadPrime.Automation.Application there is a notimplementedexception thrown.Regards

Is there documentation on this?

I would call this behavior a bug. The integral is only found if the symbolics is forced to float mode (it also happens if you use the "float" keyword).Does anybody know when it was introduced or can anybody confirm the bug in earlier versions of Mathcad than M15 M030?

Hi all!I'm trying to embed an excel file in mathcad 14 using the    insert--> component--> excel file--> "create from file" (display as icon).All I want is data from A1:A166053  (i know it is a lot of data ), this data represent the significant wave height since 1957. After I "create from file" I select 0 input and 1 output and then define the range i need. When this is done the icon appers in mathcad and I define the  name. In this case "Hs". Then the error message "The range value specified is invalid" appears...What am i missing?? Regards Sigurd Næss

So is there a way to do the second equation with symbolic operator?Shawn

If you live near Winston-Salem, NC and you are interested in attending a free user event on November 12, 2015, please check out the following link.Upcoming Events | 2015 Fall Event at TE Connectivity | Pro/Users of the CarolinasThe preliminary list of topics…Control Cross Section Area Along a Flow Path (Graph & Eval’s)Motion Analysis – Dynamics of a rotating cylinderMathcad in everyday design tasksCreo Modeling ChallengePlus, a Tour of TE Testing Labs

Постановка задачи здесь - What is not correct in this optic problem?

If   Vu=0.383*3000*(1275-d)    Vc=0.36*3000*dVu ≤ Vc Then value of  "d" ll be greater than equal to what ?

Hello,I am attempting to program a simple for loop to increment a single variable in an equation and plot the equation as a function of the variable. I have attached the mathcad worksheet. The issue arises on page 3 of the worksheet. The value I am trying to find is "Sigma_max" as "e" increases from 0 to 1 in 0.01 increments. I'm sure this is easily remedied and due to my own mathcad ineptitude. What am I missing?Thanks in advance!-Ryan

hi,how to get total number of pages in mathcad sheet in VBA or .Net.